Omron VARISPEED V7

14
 Simple Data Setting - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -50
6 Programming Features - - - - - - - - - - - - - - - - - - 52
 Hardware - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 52
 Software (Constant) - - - - - - - - - - - - - - - - - - - - - - - - - - -52
 Constant Setup and Initialization - - - - - - - - - - - - - - - - - - - - - - 53
 Constant Selection/Initialization (n001) - - - - - - - - - - - - - 53
 Using V/f Control Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - -55
 Adjusting Torque According to Application - - - - - - - - - - -55
 Using Vector Control Mode - - - - - - - - - - - - - - - - - - - - - - - - - - 59
 Precautions for Voltage Vector Control Application - - - - - 59
 Motor Constant Calculation- - - - - - - - - - - - - - - - - - - - - - 60
 V/f Pattern during Vector Control - - - - - - - - - - - - - - - - - - 61
 Switching LOCAL/REMOTE Mode - - - - - - - - - - - - - - - - - - - - 62
 How to Select LOCAL/REMOTE Mode - - - - - - - - - - - - - 63
 Selecting Run/Stop Commands- - - - - - - - - - - - - - - - - - - - - - - 63
 LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 63
 REMOTE Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -64
 Operating (Run/Stop Commands) by Communications - - 64
 Selecting Frequency Reference - - - - - - - - - - - - - - - - - - - - - - 64
 LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 65
 REMOTE Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -65
 Setting Operation Conditions - - - - - - - - - - - - - - - - - - - - - - - - 66
 Autotuning Selection (n139) - - - - - - - - - - - - - - - - - - - - -66
 Reverse Run Prohibit (n006)- - - - - - - - - - - - - - - - - - - - - 74
 Multi-step Speed Selection - - - - - - - - - - - - - - - - - - - - - - 74
 Operating at Low Speed - - - - - - - - - - - - - - - - - - - - - - - - 75
 Adjusting Speed Setting Signal - - - - - - - - - - - - - - - - - - - 76
 Adjusting Frequency Upper and Lower Limits- - - - - - - - - 77
 Using Four Acceleration/Deceleration Times - - - - - - - - - 77
 Momentary Power Loss Ridethrough Method (n081)- - - - 79
 S-curve Selection (n023) - - - - - - - - - - - - - - - - - - - - - - - 80
 Torque Detection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 81
 Frequency Detection Level (n095)- - - - - - - - - - - - - - - - - 82
 Jump Frequencies (n083 to n086) - - - - - - - - - - - - - - - - - 84
 Continuing Operation Using Automatic Retry Attempts - - 84
 Frequency Offset Selection (n146) - - - - - - - - - - - - - - - - 85