Onkyo DV CP704 User Manual

25
Basic Playback—Continued
This section explains how to start, pause, and stop play-
back.
Notes:
• During playback, you can select chapters or tracks by
using the Next [ ] and Previous [ ] buttons.
• When you stop playback of a DVD-Video disc, the
DV-CP704 remembers the point at which playback
was stopped. To resume playback from that point,
press the Play [ ] button. To cancel the Resume func-
tion, press the Stop [ ] button again. The Resume
function is reset when another disc is selected.
•With the Last Memory function you can resume play-
back from a specific point even if the disc has been
removed (see page 40).
• Do not move the DV-CP704 or subject it to vibration
during playback. Doing so may damage your discs or
DV-CP704.
• Prolonged display of the same picture or menu may
cause irreparable damage to your TV screen, known as
screen burn-in. To prevent this, don’t keep playback
paused for too long and always press the Stop [ ] but-
ton when you’ve finished playing a DVD-Video disc.
Your DV-CP704 features a screen saver to protect
your TV from the effects of burn-in (see page 46).
With some DVD-Video discs, you may experience pic-
ture noise that is not normally visible with regular TV
broadcasts. This is usually because DVD-Video discs
uses a lot of high-resolution video data. The amount of
noise, if any, will depend on your particular TV and the
problem can sometimes be alleviated by turning down
your TV’s sharpness control.
Starting, Pausing & Stopping
Playback
■ Start To start playback, press the Play
[] button.
Playback starts and the Play indica-
tor appears on the display.
If the disc is a DVD-Video, you may
need to start playback from a menu (see
page 26).
■ Pause To pause playback, press the
Pause [ ] button.
Playback pauses and the Pause indi-
cator appears on the display.
To resume playback, press the Play [ ]
button.
Playback resumes and the Pause
indicator disappears.
■ Stop To stop playback, press the Stop
[] button.
Playback stops and the Play indica-
tor disappears.
PLAY
STOP
PAUSE
ENTER
DVD
Remote controller
Remote controller
Remote controller

Onkyo DV CP704 Specifications

Operating Environment

Operating temperature	5° to 35° C (41° F to 95° F)

Power

Power supply (U.S. model)	120 V AC, 60 Hz
Power supply (Australian model)	100–240 V AC, 50/60 Hz
Power consumption	13 W
Power consumption in Standby mode (U.S. model)	0.35 W
Power consumption in Standby mode (Australian model)	0.35 W

Audio Specifications

Signal-to-noise ratio	95 dB
Audio dynamic range	95 dB
Total harmonic distortion	0.007% (1 kHz)
Wow and flutter	Below threshold of measurability

Video Outputs

Component video Y	1.0 V (p–p), 75 Ω, negative sync, RCA/phono x3
Component video PB/PR	0.7 V (p–p), 75 Ω
S VIDEO Y	0.7 V (p–p), 75 Ω, negative sync, 4-pin mini DIN x1
S VIDEO C	0.286 V (p–p), 75 Ω
Composite video	1.0 V (p–p), 75 Ω, negative sync, RCA/phono x1

Audio Outputs

Optical output	–22.5 dBm, optical connector x1
Coaxial output	0.5 V (p–p), 75 Ω, RCA/phono x1
Analog output	2.0 V (rms), 540 Ω, RCA/phono x2
HDMI output	19 pin connector

Weight and Dimensions

Weight	5.5 kg (12.1 lbs.)
Dimensions (W x H x D)	435 X 91 X 432 mm (17-1/8 X 3-9/16 X 17 ins.)