Onkyo R-811RDS User Manual

This unit has facilities for two tape decks.
If you are using only one tape deck, con-
nect it to the TAPE-1i jacks. If you have
two tape decks, connect one to the TAPE-1
jacks and the other to the TAPE-2 jacks.
|
A
OOOH
/
An
one
processor
such
as
a
graphic
L
ny
U
L
0.
UW
equalizer can be connected to these jacks.
However, if you wish to record the equal-
ized signal, it is necessary to connect a tape
deck to the TAPE REC (record) jack of the
equalizer, not to the R-811RDS.
e Turn on the PROCESSOR switch when
the PROCESSOR jacks are being used.
e When there are no components con-
nected to the PROCESSOR jacks, turn
off the PROCESSOR switch.
The MONO OUT jack can be connected to
a subwoofer amplifier, or to a subwoofer
with a built-in amplifier.
When connecting anything to the MONO
OUT jack, set the SPEAKERS A button on
the front panel to ON.
Active type
speaker

Onkyo R-811RDS Specifications

Power

power_output_at_4_ohms	2 x 50 watts
power_output_at_8_ohms	2 x 35 watts
continuous_power_output	32 watts per channel at 8 ohms
dynamic_power_output_at_4_ohms	2 x 70 watts
dynamic_power_output_at_8_ohms	2 x 40 watts
total_harmonic_distortion_at_rated_power	0.2%
im_distortion_at_rated_output	0.1%
damping_factor	40 at 8 ohms

Frequency Response

frequency_response	20Hz to 30 kHz + 1 dB
riaa_deviation	20Hz to 20 kHz + 0.8 dB

Sensitivity and Impedance

phono_sensitivity_and_impedance	2.5 mV/50 kohms
cd_tape_play_sensitivity_and_impedance	150 mV/50 kohms
tape_rec_sensitivity_and_impedance	150 mV/2.2 kohms

Signal-to-Noise Ratio

phono_signal_to_noise_ratio	80 dB (HF A, 5 mV input)
cd_tape_signal_to_noise_ratio	100 dB (IHF A)

Tuner Section

fm_tuning_range_european_models	87.50-108.00 MHz (50 kHz steps)
fm_tuning_range_worldwide_models	87.50-108.00 MHz (50 kHz steps), 87.9-107.9 MHz (200 kHz steps)
am_tuning_range_european_models	522-1611 kHz (9 kHz steps)
am_tuning_range_worldwide_models	531-1602 kHz (9 kHz steps), 530-1710 kHz (10 kHz steps)

Usable Sensitivity

fm_mono_usable_sensitivity	11.2 dBf, 1.0uV, 75 Ohms IHF
fm_stereo_usable_sensitivity	17.2 dBf, 2.0V, 75 Ohms IHF
am_usable_sensitivity	25uV

General

power_supply_european_models_except_uk	AC230V, 50 Hz
power_supply_canadian_models	AC120 V, 60 Hz
power_supply_uk_australian_models	AC240 V, 50 Hz
power_supply_worldwide_models	AC120 V and 220 V switchable, 50/60 Hz
dimensions	275 x 118 x 336 mm (10-7/8" x 4-11/16" x 13-7/32")
weight	5.5 kg, 12.1 lbs