Palax C700 COMBI - Operating Instructions for the Combustion Engine and the Winch

39 pages

Save Page as PDF

To Next Page

To Previous Page

translation

1.12 Operating instructions for the combustion engine and the winch

Refer to the manuals on our website at www.palax.fi for detailed operating and

servicing instructions for the combustion engine and the winch. In matters related to

the combustion engine turn to the nearest Honda dealer.

Main Page

Table of Contents2
Basic Specifications and Responsibilities5
Foreword5
EU Declaration of Conformity6
Intended Use of the Machine7
Warning Signs7
Type Markings8
The Main Dimensions and Models of the Machine9
Safety Instructions9
Noise Emission and Vibration10
Responsibilities of the Operator10
Operating Conditions11
Terms of Warranty11
Operating Instructions for the Combustion Engine and the Winch12
Taking Delivery and Assembly of the Machine13
State of Delivery and Acceptance Control13
Main Parts of the Machine13
Installation of the Adjustment Lever for the Splitting Wedge (Fig. 2)13
Assembly of the Log-Stop, Figure 314
Topping up Hydraulic Oil14
Bringing the Conveyor into the Work Position, Figures 4 and 514
Bringing the Conveyor into the Transport Position15
Lifting and Transferring the Machine, Figures 6A and 6B16
Driving Power17
Powered by a Tractor17
Revolutions Range of the PTO-Shaft17
Stop Switch of the Tractor-Powered Machine (Figure 7)17
Automatic Tightening of the V-Belts (Figure 8)18
Required Measures in an Emergency Situation18
Selecting the Operating Mode: Powered by Tractor or Electricity (Figures 9 and 10)18
Electric Drive, Start and Emergency Stop19
Starting19
Emergency Stop of an Electric-Motor-Powered Machine19
Starting the Electric Motor in Frost19
Honda Petrol Engine, Start, Stop and Emergency Stop20
Use of the Firewood Processor, Crosscut Operation21
Preparations before the Use of the Machine, All Models21
Operating the Crosscut Saw, before the Operation21
During the Operation21
Placing the Wood on the Deck22
Crosscut Operation22
Disturbances During Crosscut Operation and Their Remedy22
Use of the Firewood Processor, Splitting Operation23
Splitting Cylinder23
An Automatic High-Speed Valve Is Available as an Option23
Splitting Wedges23
Manual Adjustment of the Splitting Wedge, Figure 1524
Hydraulic Height Adjustment of the Splitting Wedge Fig. 16, Optional24
Adjusting the Speed of the Splitting Wedge Adjustment Cylinder, Figure 1724
Disturbances During the Splitting Operation and Their Remedy24
Re-Splitting the Logs Safely25
How the Safety Devices Affect the Operation of the Machine, Figure 1825
Operation of the Splitting Mechanism26
Solitting Sensor, Fig. 1926
Parts of the Launch Device (Figure 20)26
Operational Principle of Launching26
Hand-Start of the Splitting Motion, Figure 2127
Parts of the Hydraulic Valve (Figure 22)27
Operation of the Valve27
Maintenance of the Machine28
Crosscut Saw-Blade28
Removing the Crosscut Saw-Blade (Figures 23 and 24)28
Sharpening the Chain28
Stressing the Saw-Blade28
Guide for Crosscut Saw-Blade (Figure 25)29
Adjustment of the Saw-Blade Guide29
Automatic Tightening of the Angular Gear V-Belts, Fig. 2629
Changing the V-Belts, Angular Gear29
Changing the Oil in the Angular Gear30
Lubricating the Machine, Fig 2830
Clutch for Hydraulic Pump, Fig. 2931
Changing the Oil31
Maintenance of the Valve31
Detent End of Valve32
Lubricating the Spool Shifter, Fig. 3332
Structure of the Detent End and the Correct Order of the Parts, Fig. 3432
Initial Settings of the Valve (Figures 35 and 36)33
Adjustment of Launch Bar Clearance34
Conveyor Transmission, Fig. 3734
Conveyor Chains, Fig. 3834
Cleaning the Machine34
Washing the Machine35
Storing the Machine35

Palax C700 COMBI - Operating Instructions for the Combustion Engine and the Winch

Table of Contents

Related product manuals