To Next PageTo Next Page
Why I cannot make an outside call using One-touch Dialing on Panasonic KX-TDE100?
If you cannot make an outside call using the One-touch Dialing button or speed dialing on your Panasonic PBX, it is possible that a line access number was not stored. A line access number is required for outside calls.
What does it mean when Panasonic KX-TDE100 PBX displays 'Restricted' or gives a reorder tone?
If you are hearing a reorder tone or seeing "Restricted" displayed on your Panasonic PBX, it could be because the telephone is locked. Unlock your telephone. It's also possible that toll restriction is activated, in which case you should consult your manager or dealer. An account code may also be required.
Why paralleled single line telephones do not ring on Panasonic KX-TDE100 PBX?
If paralleled single line telephones do not ring on your Panasonic PBX, it is possible that "No ring" is selected. Change the setting to ring.
What to do if my Panasonic KX-TDE100 does not operate properly?
If your Panasonic PBX is not operating properly, try the following: * Press the Reset Button. * Turn the power switch off, then back on. * Turn off the power switch, unplug the PBX, wait 5 minutes, plug it back in, and turn the power switch back on. * If the error no. 41 is displayed in the error log, replace the IPCMEC card.
Why don't extensions work during a power outage on my Panasonic PBX?
During a power failure, if extensions connected to ports 1 to 4 of MSLC16/ SLC16 and ports 1 to 2 of DHLC8/SLC8 cards do not operate on your Panasonic PBX, it could be because a DPT or APT is connected to the extension port and the dialing mode (tone or pulse) is incorrect. Disconnect the DPT or APT and connect an SLT. Set the Tone/Pulse switch to the other position.
How to fix a Panasonic KX-TDE100 PBX display that is not shown well?
If the display is not shown well on your Panasonic PBX, change the Display contrast level.
Why are my extensions (except IP-PT/SIP Extension) not working on my Panasonic KX-TDE100 PBX?
If extensions (excluding IP-PT/SIP extensions) aren't functioning on your Panasonic PBX, the issue could stem from several sources. A malfunctioning extension card may be the cause, necessitating its replacement. Alternatively, a poor connection between the PBX and the extension could be the problem. To test this, plug the extension into the same port using a short cord; if it works, the original connection needs repair. Also, ensure that if you're using a telephone with an A-A1 relay, a 2-wire cord is used and the relay switch is in the 'OUT' or 'OFF' position. The extension itself might be faulty, so try plugging it into a working port; if it still fails, replace the extension. Lastly, confirm that the PSU is the correct type, replacing it if necessary.
What to do if I hear a busy tone when making calls using a SIP Extension on Panasonic KX-TDE100 PBX?
If you hear a busy tone when making calls using a SIP Extension on your Panasonic PBX, the port that the SIP Extension is connected to may be Out of Service. Use the Maintenance Console to change the port status from Out of Service to In Service.
How to distinguish the tones on Panasonic KX-TDE100 PBX?
To distinguish the ringing tones for each CO, ICD Group, PDN, SDN, or INTERCOM button on your Panasonic PBX (Digital proprietary telephone only), see section 3.1.4 Customizing the Buttons.
How to fix the display on Panasonic KX-TDE100?
If the display is not shown well on your Panasonic PBX, change the Display contrast level.
Details on supporting IP communication with various IP telephones and SIP extensions.
Information on using cellular phones as PBX extensions for making and receiving calls.
General safety guidelines to prevent danger and property damage during product use.
Specific considerations and limitations for users of SIP extensions.
Instructions for collecting and disposing of old equipment and batteries in the EU.
Initial setup and understanding telephone types and feature numbers.
Detailed procedures for initiating various types of calls.
Instructions on how to answer incoming calls and handle call waiting.
Managing calls during an active conversation, including transfer and hold.
Features for managing calls when away, like call forwarding.
Customizing telephone features such as alarms and DND.
Connecting and operating external devices like doorphones and relays.
Utilizing the call log and directories on display telephones.
Specific functions for IP proprietary telephones, including self-labelling.
Manager's capabilities to control and monitor other extensions.
Managing other extensions, including locking, unlocking, and status changes.
Manager's ability to change time-based service modes like Day/Night.
Personalizing telephone features and settings according to user needs.
Detailed configuration of system features and parameters via programming.
Assigning specific functions or numbers to flexible buttons for quick access.
Features available for managers to program call charges and control extensions.
Customizing system-wide settings like date, time, and speed dialling.
Common problems and solutions for telephone and PBX operation.
A table listing feature numbers and their corresponding digits or buttons.
Explanation of various audible tones used by the telephone system for feedback.
General