Why does my Panasonic PBX PS stay out of service after CS is back online?
If the PS stays out of service when the CS status is changed from Out of Service to In Service on your Panasonic PBX, it may take about 20 s for CS to start up after the status has been changed to In Service. Wait until the CS starts up.
How to troubleshoot Panasonic KX-TDE200NZ Bluetooth headset?
To resolve issues with using a Bluetooth headset with your Panasonic PBX, first ensure that the headset is properly registered to the module. Next, ensure the headset is fully charged according to its manual. Finally, remove any wired headset from the headset jack, as priority is given to wired headsets when both are connected.
Why can't I register the IP-PT on my Panasonic KX-TDE200NZ?
If you're unable to register the IP-PT on your Panasonic PBX, it might be due to: * The necessary network parameters are not set to the IP-PT: When not using a DHCP server, set the IP address, subnet mask address, and enter the PBX IP address. If necessary, also enter the IP address of the default gateway. When using a DHCP server, enter the PBX IP address.
Why is alternate calling not working on Panasonic KX-TDE200NZ?
When using a Wireless Phone (KX-T7880/ KX-T7885/KX-TD7894/ KX-TD7895) with your Panasonic PBX, if Alternate Calling—Ring/ Voice and Live Call Screening (LCS) do not function as set, it is because voice-calling mode and Hands-free mode with LCS are not available with Wireless Phones. Switch the calling mode to ring-calling. Set the LCS mode to "Private".
Why are my extensions (except IP-PT/SIP Extension) not working on my Panasonic KX-TDE200NZ PBX?
If extensions (excluding IP-PT/SIP extensions) aren't functioning on your Panasonic PBX, the issue could stem from several sources. A malfunctioning extension card may be the cause, necessitating its replacement. Alternatively, a poor connection between the PBX and the extension could be the problem. To test this, plug the extension into the same port using a short cord; if it works, the original connection needs repair. Also, ensure that if you're using a telephone with an A-A1 relay, a 2-wire cord is used and the relay switch is in the 'OUT' or 'OFF' position. The extension itself might be faulty, so try plugging it into a working port; if it still fails, replace the extension. Lastly, confirm that the PSU is the correct type, replacing it if necessary.
How to fix Panasonic KX-TDE200NZ PBX parallelled telephones not ringing?
If the parallelled single line telephones for your Panasonic PBX aren't ringing, it's possible that "No ring" is selected. Change the setting to ring.
Why some Panasonic KX-TDE200NZ PBX features do not work?
If some features on your Panasonic PBX aren't working, it could be because system management has restricted certain features; in this case, consult your manager. It's also possible that the feature numbers have changed, so confirm the revised number and try again.
How to troubleshoot Panasonic PBX telephone?
If your Panasonic PBX telephone isn't working properly, first confirm with your manager that your settings are correct. If the problem continues, it's best to consult your dealer for further assistance.
How to fix Panasonic PBX one-touch dialling?
If you cannot make an outside call using the One-touch Dialling button or speed dialling on your Panasonic PBX, it is likely that a line access number was not stored. A line access number is required for outside calls.
What to do if Panasonic PBX telephone does not respond?
If your Panasonic PBX telephone isn't responding when you press the buttons, it could be because the telephone is locked. Try unlocking your telephone. Another reason might be that your telephone is connected to an eXtra Device Port, which requires system programming. In this case, consult your dealer.
To Next Page
General