Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 141
3) Press as to select [SDI LINK], and press the <ENTER> button.
f The [SDI LINK] screen is displayed.
4) Press as to select the setting.
[AUTO]
Automatically selects the single link, the dual link, or the quad link.
Quad link will be automatically selected when the optional 3G-SDI Terminal Board with Audio (Model
No.: TY-TBN03G) is installed in both of the slots.
[SINGLE]
Sets the SDI1 input and the SDI2 input, and the SDI3 input and the SDI4 input of the Interface Board
to single link.
(Factory default setting)
[DUAL]
*1
Sets the SDI1 input and the SDI2 input, or the SDI3 input and the SDI4 input of the Interface Board to
dual link.
[DUAL/SINGLE]
*2
Sets the SDI1 input and the SDI2 input of the Interface Board to dual link, and the SDI3 input and the
SDI4 input of the Interface Board to single link.
[SINGLE/DUAL]
*2
Sets the SDI1 input and the SDI2 input of the Interface Board to single link, and the SDI3 input and
the SDI4 input of the Interface Board to dual link.
[DUAL/DUAL]
*2
Sets the SDI1 input and the SDI2 input of the Interface Board to dual link, and the SDI3 input and the
SDI4 input of the Interface Board to dual link.
[QUAD]
*2
Sets the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input of the Interface Board to quad
link.
*1 This can be selected when the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) is installed in either of the slots.
*2 This can be selected when the optional 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G) is installed in both of the slots.
5) Press the <ENTER> button.
Note
f The single link is a setting to display one image with one input signal. The dual link is a setting to display one image with two input signals.
The quad link is a setting to display one image with four input signals.
f [SDI LINK] is xed to [SINGLE] in the following cases.
g When the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] is set to anything other than [OFF]
g When the [MULTI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF] and displaying the four-screen display
f The [SDI LINK] setting cannot be changed when the [DISPLAY OPTION] menu → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE]
is set as the combination to use the SDI input of the Interface Board.
f When [SDI LINK] is set to [AUTO], use the same format for the signal to be input to the <3G-SDI 1 IN>/<3G-SDI 2 IN>/<3G-SDI 3 IN>/<3G-
SDI 4 IN> terminals. If different format signal is input to even one terminal, currently displayed image may not be projected correctly.
f [3G-SDI MAPPING] cannot be set when [SDI LINK] is set to [AUTO].
f The content set is displayed in [SDI LINK SETTINGS].
Setting [RESOLUTION] in [SLOT IN] (SDI input)
1) Press as to select [SLOT IN].
2) Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
3) Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and
press the <ENTER> button.
f The [SINGLE LINK SETTING] screen, the [DUAL LINK SETTING] screen, or the [QUAD LINK SETTING]
screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] or [QUAD LINK SETTING] is selected.
4) Press as to select [SDI1], [SDI2], [SDI3], or [SDI4], and press the <ENTER> button.
f The [SINGLE LINK SETTING] screen for the selected item is displayed.
5) Press as to select [RESOLUTION], and press the <ENTER> button.
f The [RESOLUTION] screen is displayed.
6) Press as to select an item, and press the <ENTER> button.
f Select [AUTO], [720x480i], [720x576i], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], or
[2048x1080p] when [SINGLE LINK SETTING] is selected.
f Select [AUTO], [1920x1080i], [1920x1080p], [1920x1080sF], [2048x1080p], [3840x2160p], or [4096x2160p]
when [DUAL LINK SETTING] is selected.
f Select [AUTO], [3840x2160p], [3840x2160sF], or [4096x2160p] when [QUAD LINK SETTING] is selected.
To Next Page
Loading...
