Panasonic PT-RQ35K

Chapter 4 Settings — [DISPLAY OPTION] menu
134 - ENGLISH
Note
f The automatic setup can also be executed by pressing the <AUTO SETUP> button on the remote control.
[BACKUP INPUT SETTING]
Set the backup function that switches the signal to the backup input signal as seamless as possible when input
signal is disrupted.
1) Press as to select [BACKUP INPUT SETTING].
2) Press the <ENTER> button.
f The [BACKUP INPUT SETTING] screen is displayed.
3) Press as to select [BACKUP INPUT MODE].
4) Press the <ENTER> button.
f The [BACKUP INPUT MODE] screen is displayed.
5) Press as to select the combination of the input and press the <ENTER> button.
Primary input Secondary input
Number of signals
constructing one
screen
Details
[OFF] ― Disables the backup function.
[HDMI1 [SLOT1]]
*1
[HDMI2 [SLOT1]]
*1
1
Enables the backup function.
[HDMI3 [SLOT2]]
*2
[HDMI4 [SLOT2]]
*2
[DVI-D1 [SLOT1]]
*1
[DVI-D2 [SLOT1]]
*1
[DVI-D3 [SLOT2]]
*2
[DVI-D4 [SLOT2]]
*2
[DisplayPort1 [SLOT1]]
*3
[DisplayPort3 [SLOT2]]
*3
[SDI1 [SLOT1]]
*4
[SDI3 [SLOT1]]
*4
[SDI1 [SLOT2]]
*5
[SDI3 [SLOT2]]
*5
[SDI OPT1 [SLOT1]]
*6
[SDI OPT1 [SLOT2]]
*6
[HDMI1-2 [SLOT1]]
*7
[HDMI3-4 [SLOT2]]
*7
2
[SDI1-3 [SLOT1]]
*8
[SDI1-3 [SLOT2]]
*8
[SDI1-2-3-4 [SLOT1]]
*8
[SDI1-2-3-4 [SLOT2]]
*8
4
*1 This is displayed when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This is displayed when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for DisplayPort 2 input (Model No.: ET-MDNDP10) is installed in <SLOT 1> and
<SLOT 2>.
*4 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1>.
*5 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 2>.
*6 This is displayed when the optional Interface Board for 12G-SDI Optical (Model No.: ET-MDNFB10) is installed in <SLOT 1> and <SLOT 2>.
*7 This is displayed when the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed in <SLOT 1> and <SLOT 2>.
*8 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1> and <SLOT 2>.
6) Press the <MENU> button.
f The [BACKUP INPUT SETTING] screen is displayed.
7) Press as to select [AUTOMATIC SWITCHING].
f When [BACKUP INPUT MODE] is set to [OFF], [AUTOMATIC SWITCHING] cannot be selected.
8) Press qw to switch the item.
f The items will switch each time you press the button.
[ENABLE]
Switches to the secondary input (primary input) automatically when the input signal for primary input
(secondary input) is disrupted.
[DISABLE] Disables the automatic input switching function.
Note
f The [BACKUP INPUT SETTING] setting item is common with the following menu item.
g The [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING]
f The backup function is enabled when [BACKUP INPUT MODE] is set to anything other than [OFF] and same signal is input to the primary
input and the secondary input.
f To switch to the backup input signal using the backup function, make sure that the following three conditions are satised to be ready to use
the function.
g Set [BACKUP INPUT MODE] to anything other than [OFF].