Panasonic PT-RQ35K

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 185
maximum value that can be set.
12) Adjust [LIGHT OUTPUT] of each projector.
f Adjust [LIGHT OUTPUT] of all the other projectors so that the brightness will be the same as the projector
with the least brightness.
13) Set [CONSTANT MODE] of [BRIGHTNESS CONTROL SETUP] to [AUTO], and [LINK] to [GROUP A] in
all projectors.
14) Select [APPLY] of [BRIGHTNESS CONTROL SETUP] and press the <ENTER> button in all projectors.
f Brightness control starts.
Note
f Brightness is automatically corrected whenever the light source lights up by switching on/off the projector, etc.
f When the variation in brightness has increased due to aging of the light source, or when you replaced the light source, readjust the
brightness control.
[NO SIGNAL SETTING]
Set the operation of the function when there is no input signal.
[BACKUP INPUT SETTING]
Set the backup function that switches the signal to the backup input signal as seamless as possible when input
signal is disrupted.
1) Press as to select [NO SIGNAL SETTING].
2) Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3) Press as to select [BACKUP INPUT SETTING].
4) Press the <ENTER> button.
f The [BACKUP INPUT SETTING] screen is displayed.
5) Press as to select [BACKUP INPUT MODE].
6) Press the <ENTER> button.
f The [BACKUP INPUT MODE] screen is displayed.
7) Press as to select the combination of the input and press the <ENTER> button.
Primary input Secondary input
Number of signals
constructing one
screen
Details
[OFF] ― Disables the backup function.
[HDMI1 [SLOT1]]
*1
[HDMI2 [SLOT1]]
*1
1
Enables the backup function.
[HDMI3 [SLOT2]]
*2
[HDMI4 [SLOT2]]
*2
[DVI-D1 [SLOT1]]
*1
[DVI-D2 [SLOT1]]
*1
[DVI-D3 [SLOT2]]
*2
[DVI-D4 [SLOT2]]
*2
[DisplayPort1 [SLOT1]]
*3
[DisplayPort3 [SLOT2]]
*3
[SDI1 [SLOT1]]
*4
[SDI3 [SLOT1]]
*4
[SDI1 [SLOT2]]
*5
[SDI3 [SLOT2]]
*5
[SDI OPT1 [SLOT1]]
*6
[SDI OPT1 [SLOT2]]
*6
[HDMI1-2 [SLOT1]]
*7
[HDMI3-4 [SLOT2]]
*7
2
[SDI1-3 [SLOT1]]
*8
[SDI1-3 [SLOT2]]
*8
[SDI1-2-3-4 [SLOT1]]
*8
[SDI1-2-3-4 [SLOT2]]
*8
4
*1 This is displayed when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This is displayed when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for DisplayPort 2 input (Model No.: ET-MDNDP10) is installed in <SLOT 1> and
<SLOT 2>.
*4 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1>.
*5 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 2>.
*6 This is displayed when the optional Interface Board for 12G-SDI Optical (Model No.: ET-MDNFB10) is installed in <SLOT 1> and <SLOT 2>.
*7 This is displayed when the optional Interface Board for HDMI 2 input (Model No.: ET-MDNHM10) is installed in <SLOT 1> and <SLOT 2>.