Panasonic PT-RQ35K

Chapter 4 Settings — [PROJECTOR SETUP] menu
192 - ENGLISH
[COMMAND]
Detailed settings of
[COMMAND]
Description
[INPUT]
[HDMI] Switches the input to HDMI.
[DIGITAL LINK] Switches the input to DIGITAL LINK.
[HDMI1 [SLOT1]]
*1
Switches the input to HDMI1 of the Interface Board.
[HDMI2 [SLOT1]]
*1
Switches the input to HDMI2 of the Interface Board.
[HDMI3 [SLOT2]]
*2
Switches the input to HDMI3 of the Interface Board.
[HDMI4 [SLOT2]]
*2
Switches the input to HDMI4 of the Interface Board.
[DVI-D1 [SLOT1]]
*1
Switches the input to DVI-D1 of the Interface Board.
[DVI-D2 [SLOT1]]
*1
Switches the input to DVI-D2 of the Interface Board.
[DVI-D3 [SLOT2]]
*2
Switches the input to DVI-D3 of the Interface Board.
[DVI-D4 [SLOT2]]
*2
Switches the input to DVI-D4 of the Interface Board.
[DisplayPort1 [SLOT1]]
*1
Switches the input to DisplayPort1 of the Interface Board.
[DisplayPort2 [SLOT1]]
*1
Switches the input to DisplayPort2 of the Interface Board.
[DisplayPort3 [SLOT2]]
*2
Switches the input to DisplayPort3 of the Interface Board.
[DisplayPort4 [SLOT2]]
*2
Switches the input to DisplayPort4 of the Interface Board.
[SDI1 [SLOT1]]
*1
Switches the input to SDI1 of the Interface Board.
[SDI2 [SLOT1]]
*1
Switches the input to SDI2 of the Interface Board.
[SDI3 [SLOT1]]
*3
Switches the input to SDI3 of the Interface Board.
[SDI4 [SLOT1]]
*3
Switches the input to SDI4 of the Interface Board.
[SDI1 [SLOT2]]
*4
Switches the input to SDI1 of the Interface Board.
[SDI2 [SLOT2]]
*4
Switches the input to SDI2 of the Interface Board.
[SDI3 [SLOT2]]
*2
Switches the input to SDI3 of the Interface Board.
[SDI4 [SLOT2]]
*2
Switches the input to SDI4 of the Interface Board.
[SDI OPT1 [SLOT1]]
*1
Switches the input to SDI OPT1 of the Interface Board.
[SDI OPT2 [SLOT1]]
*1
Switches the input to SDI OPT2 of the Interface Board.
[SDI OPT1 [SLOT2]]
*2
Switches the input to SDI OPT1 of the Interface Board.
[SDI OPT2 [SLOT2]]
*2
Switches the input to SDI OPT2 of the Interface Board.
[INPUT1] - [INPUT10]
*5
Switches the input to DIGITAL LINK, and switches the input of the
Panasonic twisted-pair-cable transmitter to the specied input.
[OPERATING MODE]
*6
[NORMAL] Prioritizes brightness.
[ECO] Prioritizes the life of the light source.
[QUIET] Prioritizes the operation with low noise.
[USER1] Controls the power with the setting set to [USER1].
[USER2] Controls the power with the setting set to [USER2].
[USER3] Controls the power with the setting set to [USER3].
*1 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1>.
*4 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 2>.
*5 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reected from [INPUT1] to [INPUT10]. When an item that does not reect the input name is selected, it will be disabled.
*6 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <ENTER> button.
f The command is xed and n is displayed at the left of the selected command.
f After the command is xed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 189)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.