Panasonic PT-RQ35K

Chapter 7 Appendix — Specications
ENGLISH - 311
Acoustic noise
*1
49 dB when [OPERATING MODE] is set to [NORMAL]
49 dB when [OPERATING MODE] is set to [ECO]
46 dB when [OPERATING MODE] is set to [QUIET]
Operating
environment
Operating temperature 0 °C (32 °F) to 45 °C (113 °F)
*2*3*4
Operating humidity 10 % to 80 % (no condensation)
Operation position [FLOOR/CEILING], [FRONT/REAR]
Power requirements
100 V - 120 V / 200 V - 240 V ~ (100 V - 120 V / 200 V - 240 V alternating current),
50 Hz/60 Hz
Maximum power consumption 1 150 W / 2 550 W
Standby mode power consumption 14 W
Standard outside
dimensions
Width 598 mm (23-17/32") (excluding protrusions)
Height
402 mm (15-13/16") (with the feet at shortest position, including protrusions)
353 mm (13-29/32") (excluding the feet and protrusions)
Depth 780 mm (30-23/32") (excluding protrusions)
Weight
*5
Approx. 69.8 k] (154 lbs.)
Outer case
Materials Molded plastic
Color Black
Power cord length 3.0 m (118-1/8")
Laser
Classication
Laser Class Class 1 (IEC/EN 60825-1:2014)
Risk Group Risk Group 3 (IEC 62471-5:2015)
Wireless LAN
*6
Compliance standards IEEE802.11b/g/n
Transmission method DSSS, OFDM
Frequency range
(Channel)
2 412 MHz to 2 462 MHz (1 to 11ch)
Data transfer speed
(Standard value)
IEEE802.11n Maximum 144 Mbps
IEEE802.11g Maximum 54 Mbps
IEEE802.11b Maximum 11 Mbps
Encryption method WPA2-PSK (AES)
Remote control
Power requirements DC 3 V (AA/R6/LR6 battery x 2)
Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight
150 ] (5.3 ozs.) (including batteries)
Outside dimensions Width: 47.5 mm (1-7/8"), Height: 181.5 mm (7-5/32"), Depth: 27.5 mm (1-3/32")
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2020 international standards.
*2 The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level.
*3 The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) when the optional Wireless Module (Model No.:
AJ-WM50 Series) is attached.
*4 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL] or [ECO], and the operating
environment temperature exceeds the following value, the light output may be reduced to protect the projector.
f When using the projector at an altitude lower than 2 700 m (8 858') above sea level: 35 °C (95 °F)
f When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
*5 Average value. Weight varies for each product.
*6 To use the wireless LAN function with the projector, it is necessary to attach the optional Wireless Module (Model No.: AJ-WM50 Series).
Note
f The light output will decrease to approximately 1/3 when using the projector with AC 100 V to AC 120 V.
f When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface Board for HDMI
2 input (Model No.: ET-MDNHM10), it is necessary for the rmware version of the Interface Board for HDMI 2 input to be 2.00 or later. If the
version is earlier than 2.00, the simultaneous process is not performed even if corresponding signal is input. Consult your dealer regarding
the version update to the latest rmware.
For details on how to conrm the rmware version, refer to “How to conrm the rmware version of the Interface Board (optional)”
(x page 38).
f The model numbers of accessories and optional accessories are subject to change without prior notice.