5. Repeat steps 1 through 4 for the other area
numbers,ifyouwant(2to8).
Note:
• The area title is always displayed under the
camera ID. If you specify different display
position settings for the camera ID and the area
title ID, camera ID settings must incorporate the
area title ID settings. Furthermore, when setting
the area title ID, the camera ID will be displayed
above the area title ID.
•Whether the camera ID is set to Open or Close,
camera ID will be displayed.
Whether or not the camera ID is set, when area title
ID is displayed, the camera ID will also be displayed,
but this only applies within the area title channel.
C Tilt Angle Setting (TILT ANGLE)
Selecting -5
° for the TILT ANGLE setting allows tilting
pasthorizontal,intherangeof-5
° to 185°.
1.
MovethecursortoTILTANGLE,andthentiltthejoystick
left or right to toggle the setting between -5
° and 10°.
The factory default setting is 0°.
Notes:
•ZoomingtoWIDEwhile-5
° is selected for the TILT
angle setting will cause the upper half of the
picture to become hidden.
•With certain subjects, AGC (gain control) can
cause the image to become white.
•WhentheTILTANGLEsettingisnomorethan10
°,
the dome cover may be shot
.
D Cleaning Settings (CLEANING)
This camera uses a "slip ring" for transmission of
electrical power and signals. A dirty slip ring can cause
deterioration of picture quality and generation of noise.
Thecleaningfunctionperformscleaningapprox.once
a week to keep the slip ring clean.
1. Move the cursor to CLEANING, and then tilt the
joystickleftorrighttotoggleitONandOFF.
ThefactorydefaultsettingisOFF.
The text CLEANING appears in the centre of the
screen while the cleaning process is being performed.
Note:
•Select OFF for CLEANING when the system
controller uploads or downloads the preset data.
This protects against the download or upload
failure due to start up of the cleaning process.
5. Move the cursor to POSI
, and then press the
CAM(SET)button.
This will display the ID position setting menu.
6. Use the joystick to select an area title display
position,andthenpresstheMON(ESC)button.
This registers the area title display position and
returnstotheareatitle(NESW)settingmenu.
(2)WhenON(USER)isselected
After selecting ON (USER), you can use the area title
(USER)settingmenutoconfiguredetailedsettings.
You can use the following procedure to configure
direction settings, and to input text associated with a
particular direction indicator.
1. Move the cursor to 1, and then press the CAM
(SET)button.
This will display the position setting menu. An asterisk
(*)totherightofanareatitlenumberindicatesthatit
already has an area title assigned to it.
If the there is already text associated with the
direction you selected, it will appear under the cross
mark (+). If there is no text associated with the
direction,onlythecrossmark(+)willbedisplayed.
2. Adjust the camera orientation (pan and tilt), zoom,
and focus.
Perform steps 1 through 4 under “(1) When ON
(NESW)isselected”onpage20.
3. Move the joystick to the right to align the cursor with
thetitledisplay,andpresstheCAM(SET)button.
This will display the area title setting menu.
Intheexamplescreenshowninstep1,NORTH
is the title name of area title number 1.
4. Input an area title.
The text input procedure is the same as that for
camera ID input.
See steps 3 through 5 under “Camera ID Settings”
on page 5 for informationabout inputting the text for
the area title and specifying its position on the display.
To Next Page
Loading...
