ThedirectionindicatorsareN(north),NE(northeast),E
(east), SE (southeast), S (south), SW (southwest), W
(west),andNW(northwest).
1. Move the cursor to AREA TITLE, and then tilt the
joystick left or right to turn the area title display
function on or off.
ON (NESW) : Displays direction indicators.
Selecting ON (NESW) and pressing the
CAM (SET) button will display the position
(NESW)settingmenu,whichyoucanusefor
configuringdetailedsettings.(thispage)
ON (USER) : Displaysuserinputtext.
SelectingON(USER)andpressingtheCAM
(SET) button will display the area title
(USER)selection menu,which youcan use
forconfiguringdetailedsettings.(page21)
OFF : Turns off display of area title direction
indicatorsandtext.
ThefactorydefaultsettingisOFF.
(1)WhenON(NESW)isselected
After selecting ON (NESW), you can use the position
(NESW)settingmenutoconfiguredetailedsettings.
Onceyousetthenortherly(N)directionforthecamera,
all other directions are displayed automatically.
1. Move the cursor to →PUSHSETtotherightofPAN/
TILT,andthenpresstheCAM(SET)button.
ThiswilldisplaythePAN/TILTsettingmenu.
2. Use the joystick to point the camera north, and then
presstheCAM(SET)button.
3. Move the cursor to →PUSHSETtotherightofZOOM/
FOCUS,andthenpresstheCAM(SET)button.
ThiswilldisplaytheZOOM/FOCUSsettingmenu.
4. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM(SET)button.
OFF : Picture being picked up by the camera
continues to be displayed as the camera
moves to a preset position.
ThefactorydefaultsettingisOFF.
> Digital Flip Setting (DIGITAL FLIP)
Normally, a camera needs to stop when it points
straight down during tilt. With digital flip, however, the
camera is able to tilt from 0° to 180° in a single motion.
This makes it possible to track objects passing directly
under the camera more smoothly. The picture is
flipped vertically and horizontally when the camera is
at an angle of around 135°.
1. Move the cursor to DIGITAL FLIP, and then tilt the
joystickleftorrighttotoggleitONandOFF.
ON :Turns on digital flip. Note that the tilt range
becomes 0
° to 90° when ON is selected for
thePANLIMITsetting.
OFF : Turns off digital flip. With this setting, the tilt
range is 0
° to 90°.
ThefactorydefaultsettingisON.
Notes:
•Digitalflipisperformedwhenthejoystickisheld
straight downwards only. It is not performed when
the joystick is tilted in any other direction.
•When OFF is selected for DIGITAL FLIP, the
following steps need to be performed in order to
tilt the camera 180
°.
(1) Tilt the joystick downwards to point the
camera straight down.
(2)Tiltthejoystickleftorrighttopanthecamera
180
°.
(3)Tiltthejoystickupwards.
•
MomentarilyturnoffDIGITALFLIPandsetthezoom
limit to 36x magnification or less before setting a
preset position directly from the WV-CU360C System
Controller. You can turn these functions back on
again after setting the preset position.
Note that digital flip cannot be specified for the
90
° to 180° tilt range.
A Proportional Pan/Tilt Setting (PROPO. P/T)
This function optimizes the image by automatically
adjusting the PAN/TILT (horizontal/vertical rotation)
speedaccordingtothezoomratio.
1. Move the cursor to PROPO.P/T, and then tilt the
joystickleftorrighttotoggleitONandOFF.
ON : Pan/tilt speed is in inverse proportion to the
zoomratio.
OFF : The speed is constant at the fastest level
regardlessofthezoomratio.
ThefactorydefaultsettingisON.
B Area Title Setting (AREA TITLE)
The area title function lets you display a direction
indicator that appears in the picture to indicate the
direction of the location being shown on the screen.
Text can also be displayed in place of the direction
indicators, if desired.
To Next Page
Loading...
