7. Use the joystick to point the camera at the location to
bemasked,andthenpresstheCAM(SET)button.
This registers the camera position and returns to
thezonesettingmenu.
8. Move the cursor to →PUSHSETtotherightofZOOM/
FOCUS,andthenpresstheCAM(SET)button.
ThiswilldisplaytheZOOM/FOCUSsettingmenu.
9. Move the joystick left, right, up and down to adjust
the position of the lens focus, and then press the
CAM(SET)button.
This completes the adjustment procedure and
returnstothezonesettingmenu.
Privacyzoneshouldbesetunderlowmagnification.If
theprivacyzoneissetunderhighmagnification,it
may shift.
10.Move the cursor to ZONESCALE, and then tilt the
joystickleft or right to changethe size of the zone
frame.
Shifting the setting towards the - side makes zone
frame smaller, while shifting towards the + side
makes it larger. Note, that the aspect ratio of the
zoneframeisalways3:4.Also,thesizeofthezone
frame that can be set changes according to the
zoomratio.
11. Move the cursor to SET, and then press the CAM
(SET)button.
This completes theprivacyzonesettingprocedure
andreturnstothezonenumberselectionmenu.
SelectingDELinsteadofSETdeletesthezonesettings
andreturnstothezonenumberselectionmenu.
9 Image Hold Setting (IMAGE HOLD)
Imageholdcausesthecurrentpicturetobefrozenuntil
the camera finishes moving to a preset position. This
function comes in handy when using a network interface
unit for monitoring of camera images over a network.
1. Move the cursortoIMAGE HOLD, and thentiltthe
joystickleftorrighttotoggleitONandOFF.
ON : Maintains the last image until the camera
finishes moving to a preset position.
1. MovethecursortoPRIVACYZONE,andthentiltthe
joystickleftorrighttoselectaprivacyzonesetting.
ON (1) : Turnsontheprivacyzonefunction.(Grey)
ON (2) :Turnsontheprivacyzonefunction.(Mosaic)
OFF :Turnsofftheprivacyzonefunction.
ThefactorydefaultsettingisOFF.
Usethefollowingstepstoconfigureprivacyzones.
2. Whenthecameraissetto"ON(2)",afteraccessing
thezonesetting menu by following the instructions
instep3to5,movethecursortoZONELEVEL,and
then tilt the joystick left or right to change the
concentrationoftheprivatezone.
Tosetprivatezonebyoperatingstepsafterstep3.
3. WhenPRIVACYZONEissetto"ON(1)"or"ON(2)",
movethecursortoPRIVACYZONE,andthenpress
theCAM(SET)button.
ThiswilldisplaytheZONENUMBERselectionmenu.
The picture will be wide angle (WIDE) if there is no
privacyzonedefinedforthecurrentzonenumber.
4. Move the cursor to ZONE NUMBER, and then tilt
thejoystickleftorrighttoselectthezonenumber(1
to8)youwanttoconfigure.
Anasterisk(*)totherightoftheanumberindicates
thatitalreadyhasaprivacyzoneconfiguredforit.
Selectingsuchazonenumberzoomsthepictureto
thezoomsettingthatwasineffectwhenitsprivacy
zonesettingswereconfigured.
5. PresstheCAM(SET)button.
This will display the zone setting menu. The
appearanceofthemenudependsonzonesettings.
The currently configured zone frame will appear in
the centre of the picture.
Performing the remaining steps of this procedure
will delete the current zone frame and replace it
withthenewzoneframethatyouconfigure.
6. Move the cursor to →PUSHSETtotherightofPAN/
TILT,andthenpresstheCAM(SET)button.
ThiswilldisplaythePAN/TILTsettingmenu.
To Next Page
Loading...
