Notethatthetotalpatroltimeistwominutes,andthe
time allowed for each routine depends on the number
of patrol routines that are configured. The values in
parentheses indicate the time of each patrol routine
(twominutesforonepattern,oneminuteeachfortwo
patterns,30secondseachforfourpatterns).
If you want to change the number of patrol routines
from a previous setting, first delete all of the
currently store patrol routines. To delete everything,
move the cursor to RESET, and press the CAM
(SET)button.
3. Move the cursor to a PATROL number (PATROL 1
through 4), and then tilt the joystick left or right to
select a patrol setting.
--- : Disables the selected patrol routine.
PLAY : Performstheselectedpatrolroutine.(see
thispage)
LEARN : Select this option to teach the camera a
series of movements (patrol routine). (An
asterisk(*)totherightofaPATROLnumber
indicates that it already has a patrol routine
assignedtoit.)(seethispage)
DEL → PUSH SET : PresstheCAM(SET)buttonto
de l e t e a n e x i st i n g p a tro l
routine.
<When PLAY is selected>
(1) Pressthesystemcontroller’sF2buttontoclose
the menu.
The orientation of the camera moves to the
stored start position, and the camera starts to
playback the stored movement.
(2) When the playback is finished, manually pan,
tilt,zoomandfocus.
<When LEARN is selected>
(1) Pressthesystemcontroller’sF2buttontoclose
the menu.
The start position is stored, and the camera’s
movements can be stored.
(2) Operatethecameratostorethemovements.
“LEARNING(***S)”isdisplayedinthecentreof
the screen when the movements are being
stored.(unit:sec)
* “(***S)” indicates the amount of time that
remains for storing movements.
(3) Thesetupmenuisdisplayedandteachingstops.
Storing movements stops when the remaining
time reaches “0S”.
Notes:
•Selecting LEARN to teach the camera a patrol
routine causes the following parameters to be
stored along with the camera movements.
(1) ParametersattheBeginningoftheRoutine
• PAN,TILT,ZOOM,andFOCUSpositions
• IRIS level
• Shutterspeed(SHUTTER)
• Gain(AGC)setting
• Electronic sensitivity enhancement (SENS
UP)setting
• Whitebalance(WHITEBAL)setting
(2)DuringCameraMovement
• PAN,TILT,ZOOM,andFOCUSpositions
• IRIS operation
• Preset positioning
• The auto-focus function does not work during
patrol operations. The image goes out of focus
when the camera zooms in from a wide angle
(WIDE), this is caused by th e z o o m l e n s
mechanism. The fuzziness in the image can be
reducedbystartingfromatelephotoangle(TELE)
whenregisteringazoomoperation.
• In the patrol play mode, black and white
automatic switching does not work.
•
In the patrol play mode, when the power of the
system controller is turned on or off, the patrol play
stops. In this case, press the PATROL PLAY button
again.(IfSELFRETURNissettoON,thepatrolplay
willstartagainafterelapsingthesettingreturntime.)
•Patrolmovementcoversarangefromhorizontalto
directly below the camera. The digital flip function
(page20)doesnotoperate.
• When you want to stop before the patrol memory
is finished, either click "STOP" when the system
controllerisinLEARNmodeoropenthemenu.
8 Privacy Zone Setting (PRIVACY ZONE)
The privacy zone function makes it possible to mask
specific areas of the scene (screen) from view. Up to
eightprivacyzonescanbeconfigured.
Notes:
•Certain camera orientations can cause privacy
zonemaskedareatobecomevisible.
•The privacy zone function does not mask scene
areas during the initialisation routine performed
immediately after camera power is turned on.
•The zone position may shift if the stabilizer
settingsarechangeaftersettingtheprivacyzone.