4. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select the start point and end
point dwell time setting.
Tilting the joystick cycles through the stop time
displayinthesequenceshownbelow.(unit:sec)
The factory default setting is 1S.
5. Move the cursor to PAN LIMIT, and then tilt the
joystickleftorrighttotoggleitONandOFF.
ON :Limits manual panning to the zone between
the start point and the end point. The TILT
range is from horizontal to straight down.
Select OFF for the ENDLESS setting (step 3)
when using this setting.
OFF :Allows manual panning outside the zone
between the start point and the end point.
ThefactorydefaultsettingisOFF.
PAN LIMIT
PAN LIMIT allows panning in the area from the start
point to the end point specified in step 1, but not in the
area from the end point to the start point.
6 AUTOPAN Key Setting (AUTOPAN KEY)
Set the operations of the camera when AUTOPAN is
executedfromthesystemcontroller.(page16)
1. MovethecursortoAUTOPANKEY,andthentiltthe
joystick left or right to select a camera movement
mode setting.
Tilting the joystick cycles through settings in the
sequence shown below.
ThefactorydefaultsettingisAUTOPAN.
Notes:
•Auto Mode can be started, but not stopped, with
theAUTOPANkey.
•PATROL1-4displaysonlythesetnumberofpatrol
routines(thispage).
7 Patrol Function Setting (PATROL)
The patrol function remembers manual operations for
later automatic playback when they are needed.
1. Aim the camera, with the menu closed, at the start
point of the routine you want it to remember.
2. MovethecursortoNUMBER,andthentiltthejoystick
left or right to specify the number of patrol routines.
Tilting the joystick cycles through settings in the
sequence shown below. The amount of storage
time available depends on the number of routines.
The storage time display changes in the sequence
shownbelow.(unit:sec,min)
Thefactorydefaultsettingis1(2MIN).
Notes:
•The auto mode is exited automatically whenever
manualPAN/TILT or ZOOM/FOCUS isperformed if
AUTOPAN is operating and PAN/TILT does SEQ,
SORT,PATROL, or AUTOTRACK movement. Note,
however, that that the contents of the setting menu
do not change. To return to the auto mode, open the
setup menu and then close it again. The auto mode
will also activate when the self return trigger time
(page16)elapses.
•During operation, the lens may enter the refresh
mode.
• PATROL1-4displays onlythe set number of
patrolroutines(thispage).
l Configuring AUTOPAN Detailed
Settings
1. Perform the following steps to set the PAN start
point and end point.
(1) Move the cursor to POSITION, press the CAM
(SET) button, and then move the cursor to
START.
(2) Use the joystick to move the camera to the
desiredPANstartpoint,andthenpresstheCAM
(SET)button.
This defines the start point and moves the
cursortoEND.
(3) Use the joystick to move the camera to the
desiredPANendpoint,andthenpresstheCAM
(SET)button.
This defines the start point and moves the
cursortoPOSITION.
2. Move the cursor to SPEED and then tilt the joystick
left or right to select a panning speed setting.
Shifting the setting towards the “H” (right) side
increases the speed, while shifting towards the “L”
(left)sidedecreasesit.
The factory default setting is 128.
3. MovethecursortoENDLESS,andthentiltthejoystick
left or right to turn endless panning on or off.
ON : Pans from the start point to the end point,
and then continues to pan in the same
direction from the end point to the start point.
SelectOFFforthePANLIMITsetting(step5)
when using this setting. Panning will be
repeated endlessly.
OFF : Pans from the start point to the end point,
and then reverses direction to pan from the
end point to the start point. Panning is
repeated endlessly.
ThefactorydefaultsettingisOFF.
To Next Page
Loading...
