Note:
•Size and speed limitations are relaxed somewhat
when the contrast ratio between the background
and the moving object is large.
6. Move the cursor to DWELL TIME, and then tilt the
joystick left or right to select an alarm detect dwell
time setting.
Afteralarmdetection,thenextalarmisnotdetected
until the specified dwell time elapses.
Tilting the joystick cycles through the setting display
inthesequenceshownbelow.(unit:sec)
The factory default setting is 2S.
7. Move the cursor to RECOVER TIME, and then tilt
the joystick left or right to select an alarm reset time
setting.
Tilting the joystick cycles through the setting display
inthesequenceshownbelow.(unit:sec,min)
If you set OFF, then it does not reset until some
other operation is done. If AUTOTRACK is set, the
camera starts automatic tracking when change
(movement)isdetectedintheimageduringSEQor
SORT.
ThefactorydefaultsettingisOFF.
Notes:
•Monitoring is usually done in SEQ mode, and
when the camera detects change (movement)
automatic tracking starts. To have the camera
return to SEQ mode after a certain amount of time,
settheSELFRETURNsettingtoSEQ.
•Usethemasksettingtomaskareaswherethereis
wind movement of curtains, etc.
•Use a lower sensitivity level (LEVEL) setting for
areas where illumination is low and prone to digital
noise. Also note that operation error can occur
when the illuminance of a subject is changed
suddenly by the headlights of passing cars,
turning lights on or off, etc.
•There is a delay of about 0.2 second from the
pointthatthecameradetectschange(movement)
in the image and the point that a signal is sent to
the alarm terminal of a VTR, etc.
•Alarms are not output while the setting menu is
displayed, unless demo mode alarm output is
turned on.
•Alarms are not output when PAN, TILT, ZOOM,
FOCUSorotherfunctionsareoperating.
•When the motion detector is set to MOTION DET
orSCENECHANGE,itoutputsalarm data during
the blanking period. This can cause operational
problems for a VTR or other device that uses a
time code signal, etc. Turn off the motion detector
whennotusingcoaxialcommunication.
•The motion detector is not intended for use as
specialty device for the prevention of theft, fire,
etc. The manufacture assumes no responsibility
for any accidents that occur or any losses
incurred while this product is being used.
•When in the preset position the preset position
settings are in effect.
2 Preset Alarm Setting (PRESET ALM)
Turning on the preset alarm will output an alarm from
the video output port or alarm output connector when
the camera completes a move to a preset position. An
alarm is output in the following cases.
• Whentheselfreturnfunctionisactivated(page16)
and the camera finishes moving to the home
position, and when switching to the auto mode.
• WhenSEQisselectedfortheautomode(page16),
and the camera completes a move to a preset
position during sequential movement
• When SORT is selected for the auto mode (page
16),andthecameracompletesamovetoapreset
positionduringSORTmovement
• WhenAUTOPANisselectedfortheautomode,and
the camera completes a preset move up to the
AUTOPANstartpoint
• When the camera completes a move to a preset
position during manual operation
• WhenPLAY isselectedforthePATROLmode, and
the camera completes a preset move up to the
patrol start point
Use the following procedures to configure preset alarm
settings
1. Move the cursor to PRESET ALM, and then tilt the
joystickleftorrighttotoggleitONandOFF.
ON : Turns on the preset alarm function.
OFF : Turns off the preset alarm function.
ThefactorydefaultsettingisOFF.
Note:
•Tur n off th e preset al a r m fu n ction be fore
downloading or uploading preset data.
3 Alarm Input/Output (ALARM IN/OUT)
Use this setting to specify what operation the camera
should perform when it an alarm signal is input to the
alarm input connector or output from the alarm output
connector.
1. MovethecursortotheALARMIN/OUT
and then
presstheCAM(SET)button.
This will display the alarm setting menu.
2. Move the cursor to ALARM IN 1, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
receivedbyALARMIN1.
OFF : Ignore alarm input signals.
1POSI : Move to preset position 1.
AUTOPAN : Start autopan.
PATROL1 :StartPATROL1.
AUTOTRACK1 : Move to preset position number 1,
and then perform auto tracking.
PATROL1 (S) :Start PATROL 1, and maintain the
stored picture quality settings
(page17)evenaftercompletion.
ThefactorydefaultsettingisOFF.
To Next Page
Loading...
