3. Move the cursor to ALARM IN 2, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
receivedbyALARMIN2.
OFF : Ignore alarm input signals.
2POSI : Move to preset position 2.
SEQ : Start sequential movement.
PATROL2 :StartPATROL2.
AUTOTRACK2 : Move to preset position number 2,
and then perform auto tracking.
PATROL2 (S) :Start PATROL 2, and maintain the
stored picture quality settings
(page17)evenaftercompletion.
ThefactorydefaultsettingisOFF.
4. Move the cursor to ALARM IN 3, and then tilt the
joystick left and right to select the operation the
camera should perform when an external signal is
receivedbyALARMIN3.
OFF : Ignore alarm input signals.
3POSI : Move to preset position 3.
SORT : Start sort movement.
PATROL3 :StartPATROL3.
AUTOTRACK3 : Move to preset position number 3,
and then perform auto tracking.
PATROL3 (S) :Start PATROL 3, and maintain the
stored picture quality settings
(page17)evenaftercompletion.
ThefactorydefaultsettingisOFF.
5. MovethecursortoALARMIN4,andthentiltthe
joystick left and right to select the operation the
camerashouldperformwhenanexternalsignalis
receivedbyALARMIN4.
OFF : Ignore alarm input signals.
4POSI : Move to preset position 4.
BW : Black and white display while
signal is being input.
PATROL4 :StartPATROL4.
AUTOTRACK4 : Move to preset position number 4,
and then perform auto tracking.
PATROL4 (S) :Start PATROL 4, and maintain the
stored picture quality settings
(page17)evenaftercompletion.
ThefactorydefaultsettingisOFF.
Notes:
•Use PATROL 1 (S) to 4 (S) if you want to switch
picture quality (for example to switch picture
quality from day to night) when an alarm input is
received.ALARMIN4canbeusedcombinedwith
BW.
To use the camera with this application, set the
picture quality you want to switch before
registering the patrol, then start the patrol
registration and then end the registration
immediately.
•If youwantto change the picturequality settings
accordingtoalarminputforPATROL1(S)to4(S),
the settings are applied to the camera settings
and are kept even after the camera is turned on
again.
•PATROL1(S)-4(S)displaysonlythesetnumberof
patrolroutines(page17).
6. Move the cursor to CNT-CLS 1, and then tilt the
joystick left and right to select the alarm output that
shouldbeperformedoverALARMOUT1whenan
alarm is detected.
OFF :Noalarmoutput
AUX1 :Output a contact close signal when
AUX1 input is received from the system
controller.
ALARM :Output an alarm signal when an alarm is
detectedbythemotiondetector(page22)
or the preset alarm (page 23). After
selecting this setting, perform step 7 to
specify the alarm signal output time.
ThefactorydefaultsettingisOFF.
7. Move the cursor to TIME OUT and then tilt the
joystick left and right to select the alarm signal
output time.
Tilting the joystick cycles through the output time
displayinthesequenceshownbelow.(unit:ms)
The factory default setting is 100MS.
8. Move the cursor to CNT-CLS 2, and then tilt the
joystick left and right to select the alarm output that
shouldbeperformedfromALARMOUT2whenan
alarm is detected.
OFF :Noalarmoutput
AUX2 :Output a contact close signal when
AUX2 input is received from the system
controller.
BW :Output a contact close signal only while
the camera is in the black and white
mode.
ThefactorydefaultsettingisOFF.
9. Move the cursor to COAX ALM OUT, and then tilt
thejoystickleftorrighttotoggleitONandOFF.
This setting turns alarm controls whether an alarm is
output when the camera moves to one of the preset
positionsspecifiedforALARMIN1through4(1POSI,
2POSI,3POSI,4POSI)insteps2through5,above.
ON :Output an alarm signal from the video
output connector at the point the camera
finishes moving to a preset position
(number1through4)whenthereisalarm
inputtoALARMIN(1through4).
OFF :Noalarmsignaloutput
ThefactorydefaultsettingisOFF.
Notes:
•The camera ignores alarm inputs during manual
operation.
•Turn offalarm outputswhen the system controller
downloads or uploads the preset data.
To Next Page
Loading...
