To Next PageTo Next PageWhat to do if Panasonic WV-SW598 live indicator never lights up?
If the live indicator never lights up, check whether “Off” is selected for “Link/Access LED” on the “Basic” page and select “On” or “On(Access)” for the indicator setting.
What to do if my Panasonic WV-SW598 Security Camera live indicator lights red?
A red live indicator suggests an issue with the SD memory card. Here's what to check: * Ensure the write protect switch of the SD memory card is not set to “LOCK”. Unlock it. * Make sure the SD memory card was formatted on the camera, not a PC. Use a card formatted on the camera. * The SD memory card might be faulty; replace it with a working card.
What to do if Panasonic Security Camera doesn't move to preset positions accurately?
Execute the position refresh function of your Panasonic Security Camera.
What to do if Panasonic Security Camera starts panning unpredictably?
Unpredictable panning may be due to noise. Check the exogenous noise level around the camera.
Why is my Panasonic WV-SW598 power not turned on?
If the power is not turning on, check the connection. If you are using a PoE+ device for power, ensure the connection is properly established. If you are using AC power, ensure that connection is appropriately established.
What to do if Panasonic Security Camera audio input contains noise?
If you're experiencing noise in the audio input, consider the following: * Check the grounding of the camera, switching hub, and any peripheral devices. * Verify the camera's location; it might be too close to an electrical power line or a device producing strong magnetic fields or radio waves. * Try using a powered microphone or connecting an audio output with low output impedance.
Why is the live indicator on my Panasonic Security Camera blinking orange when I turn it on?
The live indicator might blink orange for several reasons: * The LAN cable might not be properly connected, so ensure it is. * The hub or router connected to the camera may not be working correctly, so check its operation. * The LAN cable connected to the camera might be broken, so try replacing it with a new one.
What to do if Panasonic Security Camera cannot download the log list?
To resolve the issue of not being able to download the log list from your Panasonic Security Camera, you may need to enable file downloads in Internet Explorer. In the security settings, select 'Enable' for 'Automatic prompting for file downloads'.
Why is no image displayed on my Panasonic Security Camera?
If no image is displayed from your Panasonic Security Camera, ensure that the viewer software is installed on your PC. This software is required to view the camera's video feed.
Why does my Panasonic WV-SW598 Security Camera authentication window keep popping up?
If you're repeatedly seeing the authentication window when trying to access your Panasonic Security Camera, try closing the web browser and accessing the camera again. This issue may occur if the username or password has been changed, or if there were changes to the authentication settings.
General| Type | IP security camera |
|---|---|
| PTZ control | Yes |
| Certification | UL (UL60950-1), C-UL (CAN/CSA C22.2 No.60950-1), CE, IEC60950-1, EMC, FCC Part15 Class A, ICES-003 Class A, EN55022 Class B, EN55024 |
| Placement supported | Indoor & outdoor |
| Connectivity technology | Wired |
| Form factor | Dome |
| Mounting type | Ceiling |
| Product color | Black, Silver |
| International Protection (IP) code | IP66 |
| Total megapixels | 2.4 MP |
| Maximum resolution | 1920 x 1080 pixels |
| Supported video modes | 1080p, 720p |
| Video formats supported | H.264 |
| Pan range | 0 - 360 ° |
| Pan speed | 0.065 °/sec |
| White balance | ATW |
| Minimum illumination | 0.004 lx |
| Sensor type | MOS |
| Optical sensor size | 1/3 \ |
| Digital zoom | 12 x |
| Optical zoom | 30 x |
| Focal length range | 4.3 - 129 mm |
| Built-in HDD | - |
| Compatible memory cards | SD, SDHC, SDXC |
| Cabling technology | 10/100Base-T(X) |
| Supported network protocols | IPv6:TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP, SNMP, DHCPv6 , ICMP, ARP; IPv4:TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP |
| Ethernet LAN (RJ-45) ports | 1 |
| Power consumption | 470 mA |
| Power source type | PoE |
| Still image resolution(s) | 1920 x 1080, 640 x 360, 320 x 180, 1280 x 720, 1280 x 960, 320 x 240, 640 x 480 |
| Number of simultaneous users | 14 user(s) |
Weight and Dimensions| Height | 392 mm |
|---|---|
| Weight | 5000 g |
| Diameter | 229 mm |
Explains how the camera responds to various alarm events and notifications.
Describes how to automatically transmit alarm images to an FTP server.
Lists and explains the camera's built-in security features like authentication and HTTPS.
Guides users on accessing the camera's setup menu via a web browser.
Explains how to navigate and configure settings within the camera's setup menu interface.
Covers essential camera settings like title, date/time, and SD card configuration.
Explains how to configure settings for the SD memory card, including recording format.
Details how to configure terminal settings, VMD, audio detection, and command alarms.
Configures camera actions (preset, auto track, patrol) for different alarm triggers.
Details how to configure HTTPS settings for secure camera access and certificate management.
Explains the process of upgrading the camera's firmware to the latest version.
Explains how to reset camera settings to default or reboot the unit.
