Pandora Mini v3 User Manual

3130
USER MANUAL
PANDORA MINI V3 CAR SERVICE-SECURITY SYSTEM
Note! see the “INfoRmAtIoN” sectIoN foR descRIptIoN of sIGNAls INdIcAtING the
NumbeR of RecoRded coNtRol devIces
Pandora Alarm Studio
The Pandora Alarm Studio allows configuring the main parameters of the
system, uploading firmware updates, downloading installation guides, making
the “Pandora CLONE” procedure.
In preparation to programming, these stages should be followed:
• Install the Pandora Alarm Studio to a PC with Windows XP/Vista/7/8/10;
• Start the Pandora Alarm Studio;
• Connect the system and PC via a USB cable;
• Enter the programming mode by entering the service PIN-code;
• The application will automatically open the settings window.
It is recommended to update firmware of the base unit before installing
and programming the system (actual version of the firmware you can down
-
load from pandorainfo.com or from the Alarm Studio). You can update firmware
using the Alarm Studio application after entering the programming mode:
• Press the “Update software” button and select a type of updating;
• “Load from file” – select previously downloaded firmware on your PC, “Firm-
ware archive” - firmware will be downloaded from a server to the “firm-
wares” folder.
• Select a firmware file and press the “Update” button;
Exit the programming mode after changing the settings or updating firmware.
Note! If AN updAtING pRocess hAs beeN INteRRupted foR some ReAsoN ANd the
stAtus INdIcAtoR lIGhts Red, you Need to use the “quIck boot mode” to uploAd
fIRmWARe. opeN the AlARm studIo; de-eNeRGIze ANd dIscoNNect the system; pRess
ANd hold the vAlet buttoN locAted oN the bAse uNIt; ReleAse the buttoN Im-
medIAtely AfteR coNNectING the system ANd A computeR vIA usb cAble; the system
WIll eNteR the boot mode.
Programming menu
Enter the programming mode, enter the “Service PIN-code” (default value is
1-1-1-1), the system will wait for level input – “Level 0 Entering a level”. Enter
a desired level using the VALET button (see the “Programming levels table”)
to change settings or parameters. . The system will confirm correct input with
red LED flashes and short sound signals of the siren/beeper and proceed to
the desired level.
AN EXAMPLE
• To enter a level (“Level №1…№17”), press (P) the VALET button the number
of times equals to the desired level number (1…17), pauses between press-
es should not exceed 1 second. The system will confirm correct input with
red LED flashes and short sound signals of the siren/beeper and proceed
to the desired level. To enter a sublevel or a cell of sublevel make a pause
for more than 1 second (), then press (P) the VALET button the number of
times equals to the desired sublevel or cell number.
• For quick access to the higher level, press and hold (H) the VALET button.
The siren will sounds tone beeps (up to 10). These sounds means the se-
quence number of a two-digit level number (the first signal – level №10, the
fifth signal – level №50, the tenth signal – level №100). Release the VALET
button immediately after the desired number of signal. To enter an interme-
diate level (Level №11…№17), press the VALET button the number of times
equals to the second digit (1…7) of the desired level number immediately
after releasing the button. The system will confirm correct input with red
LED flashes and short sound signals of the siren/beeper and proceed to the
desired level.

Pandora Mini v3 Specifications

General

Brand	Pandora
Model	Mini v3
Category	Security System
Language	English