Hydraulic and Electrohydraulic Actuators
HAS Series Analog Drives Manual
81
Parker Hannifin Corporation
Cylinder Division
Des Plaines, Illinois USA
www.parker.com/cylinder
Catalog HY08-4005-M3
WARNING: This product can expose you to chemicals including Lead and Lead Compounds which are known to the State of
California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
PROP 65 WARNING
TThhee DDIIAAGGNNOOSSTTIICC MMeennuu
DDIIAAGGNNOOSSTTIICC MMEENNUU
PPRREEFF 66551111 DDiissppllaayy 66990011 DDiissppllaayy
101.09 SSPPEEEEDD DDEEMMAANNDD
RRaannggee:: —.xx %
Indicates actual speed demand. This is the input to the frequency controller.
(Refer to the REFERENCE function block)
101.01 RREEMMOOTTEE SSEETTPPOOIINNTT
RRaannggee:: —.xx %
This is the target reference that the drive will ramp to in remote reference mode (not including
trim), direction is taken from REFERENCE::REMOTE REVERSE and the sign of REMOTE
SETPOINT.
(Refer to the REFERENCE function block)
101.14 CCOOMMMMSS SSEETTPPOOIINNTT
RRaannggee:: —.xx %
This setpoint is the target reference that the drive will ramp to in Remote Reference Comms mode
(not including trim). The direction is always positive, i.e. forward.
(Refer to the REFERENCE function block)
101.12 LLOOCCAALL SSEETTPPOOIINNTT
RRaannggee:: —.xx %
Indicates the Keypad setpoint. It is always a positive quantity; saved on power down. Direction is
taken from LOCAL REVERSE.
(Refer to the REFERENCE function block)
103.01 ((JJOOGG)) SSEETTPPOOIINNTT
RRaannggee:: —.xx %
The setpoint is the target reference that the drive will ramp to in Jog Reference mode.
(Refer to the REFERENCE JOG function block)
83
wwwwww..ppaarrkkeerr..ccoomm/
cylinder
Diagnostic Menu
DDIIAAGGNNOOSSTTIICC MMEENNUU
PPRREEFF 66551111 DDiissppllaayy 66990011 DDiissppllaayy
78.17 TTOOTTLL SSPPDD DDMMDD RRPPMM
RRaannggee:: —.xx rpm
The final value of speed demand obtained after summing all sources in rpm.
(Refer to the SPEED LOOP function block)
78.18 TTOOTTAALL SSPPDD DDMMDD %%
RRaannggee:: —.xx %
The final value of speed demand obtained after summing all sources as a percentage of MAX
SPEED CLAMP (REFERENCE function block).
(Refer to the SPEED LOOP function block)
70.04 SSPPEEEEDD FFBBKK RRPPMM
RRaannggee:: —.xx rpm
The mechanical speed of the motor shaft in revolutions per minute.
(Refer to the FEEDBACKS function block)
70.06 SSPPEEEEDD FFBBKK %%
RRaannggee:: —.xx %
Shows the mechanical speed of the motor shaft as a percentage of MAX SPEED CLAMP
(REFERENCE function block).
(Refer to the FEEDBACKS function block)
78.19 SSPPEEEEDD EERRRROORR
RRaannggee:: —.xx %
The difference between the demanded speed and the actual speed.
(Refer to the SPEED LOOP function block)
73.04 DDRRIIVVEE FFRREEQQUUEENNCCYY
RRaannggee:: —.xx Hz
Shows the drive output frequency in Hz.
(Refer to the PATTERN GEN function block)
84
wwwwww..ppaarrkkeerr..ccoomm/
cylinder
To Next Page
Loading...
