48
EasyTouch Control System User’s Guide
Settings Menu: F° / C° (Fahrenheit/Celsius)
The temperature settings for the water, solar and air can be displayed in either Fahrenheit or Celsius.
F° / C°
To change the temperature units:
Up/Down buttons: Select either Fahrenheit or Celsius. Press the Menu button to
save the settings and to return to the Settings menu options. Press the Menu button
again to return to the main menu options or press again to return to the main screen.
Settings Menu: iS4 Spa-Side Remote Controller
You c a n specify any iS4 Spa-Side r e m o t e button to control different functions b y assigning each button to a
specific circuit. For example, you can use the iS4 Spa-Side remote to activate the spa circulation and for
operating auxiliary equipment such as heater, lights, jet pump, heat boost, air blower, waterfall, etc.). You can
also use the “Pump Incrs” and “Pump Decrs” circuit to increase or decrease the pump speed for an IntelliFlo
VF (GPM) or VS (RPM) pump. For example, if the “Pump Incrs” circuit is assigned to an iS4 button, each
press of the button will increase the pump speed in specific speed increments as specified in the “10 B Pump
Cntrl” menu setting (see page 50). Speed increments are set from 10 to 250 RPM (or 1 to 10 GPM, for the
IntelliFlo VF).
Assign iS4
Before configuring the iS4 Spa-Side remote controller assign names to the circuits (see page 41).
To assign iS4 Spa-Side buttons:
Up/Down buttons: Select a circuit to one of the iS4 buttons. You can set up to four
circuits (1/4, 2/4, 3/4, 4/4).
Right button: Move to the circuit setting.
Up/Down buttons: To configure the first button on the iS4 Spa-Side Remote, scroll
through the circuit names and find the circuit that you would like to assign to the first
button on the iS4. The generic circuits are: NONE, SPA, POOL, AUX 1-7
(EasyTouch 8), AUX 1-3 (EasyTouch 4), FEATURE 1-8, SOLAR (if selected in
“Heat” menu), AUX EXTRA, HEAT BOOST, HEAT ENABLED, PUMP
INCRS, PUMP DECRS. AUX EXTRA is available if the Solar output (J17) plug on
the EasyTouch motherboard is not being used for solar equipment. Use the Solar
button to switch the extra circuit on and off (see page 5). Selecting “NONE” does not
assign a circuit.
Note: The “HEAT BOOST” feature will switch on the heater for seven minutes to
increase the spa water temperature. Each time the spa Heat Boost button is
pressed, the temperature will increase about 1
° F (-17° C). The temperature will
not go beyond the 104° F (40° C) limit.
Right button: Assign the next circuit (2/4).
Up/Down buttons: Select the first digit for the circuit number (1/4, 2/4, 3/4, 4/4) and
repeat the procedure for the other three buttons.
Press the Menu button to save the settings and to return to the Settings menu
options. Press the button again to return to the main menu options or press again to
return to the main screen.
MENU ▼ SETTINGS ▼ IS4 ASSIGN IS4
Getting There
▲
T
F° / C°
FAHRENHEIT
S
MENU ▼ SETTINGS ▼ F˚ / C˚ F˚ / C˚
Getting There
▲
T
Assign iS4
Circuit: 1/4
[HEAT BOOST ]
S
Note: To
disable or
enable the
iS4 Spa-Side
remote, see
Settings
Menu: Spa
Side,” on
page 55.
To Next Page
Loading...
Need help?
General
