27640 -19/34-
3） W65(t=0.5) x3, M 103 x3
4） [
[[
[Adjust
AdjustAdjust
Adjust]
]]
] Install AF block for temporary.
Tighten M103 until it stops and then
return for about 1.5 turns.
(If the final adjustment is over, apply screw lock
between M103 and W65. )
[
[[
[Note
NoteNote
Note]
]]
] There should not be any dust, hair or
stain on AF window of 0-M100.
4
44
4-
--
-9
99
9. 0
. 0. 0
. 0-
--
-S300(AF Motor block)
S300(AF Motor block)S300(AF Motor block)
S300(AF Motor block)
5） Adhere S364 onto 0-S300.
6） Arrange lead wires and Flexi. as shown in Fig.
7） 0-S300, 2 screws.(Apply screw lock.)
8） Arrange lead wires.
4
44
4-
--
-10.
10. 10.
10. [A
[A[A
[Adjust
djustdjust
djust･
･･
･Check] AF joint stroke.
Check] AF joint stroke.Check] AF joint stroke.
Check] AF joint stroke.
[Prepared material] Caliper
1) Set Focus mode lever at “AF”. If 0-I331 is installed, set at the lowest one.
2) [Check]
[Check][Check]
[Check] When removing finger from Mount lock lever, AF joint pin(0-S300) should be
stuck out more than 1.2mm above body mount.
3) [Check]
[Check][Check]
[Check] While pushing mount lock lever and mount lock pin become same height with
camera mount, AF joint pin should not exceed the surface of camera mount.
[Adjust]
[Adjust][Adjust]
[Adjust] Adjusting can be done by turning eccentric screw of 0-A121(Joint connecting
lever). Apply screw lock on the eccentric screw.
5） [Check]
[Check][Check]
[Check] After depressing mount lock lever and then
set free, 0-A121 should return smoothly.
4
44
4-
--
-1
11
11
11
1.
..
.
L3
L3L3
L3・
・・
・L2(Penta Prism
L2(Penta PrismL2(Penta Prism
L2(Penta Prism・
・・
・Focus screen)
Focus screen)Focus screen)
Focus screen)
1） M3
2） L3（M8 x2,M18,M19）･ ･ ･ Loosen M16 x2 beforehand.
3） M61、M62 x2(Hook M61 to M63)
4） 0-M301、2 screws.
5） M22(Install –00C for temporary adjustment), L2
4
44
4-
--
-12
1212
12. [Adjust
. [Adjust. [Adjust
. [Adjust･
･･
･Check] Focus in finder
Check] Focus in finderCheck] Focus in finder
Check] Focus in finder・
・・
・Parallax
ParallaxParallax
Parallax.
. .
.
[Prepar
[Prepar[Prepar
[Preparation
ationation
ation]
]]
] Collimator、Focus master lens.
1） Adjust diopter by turning 0-M301 at center of frame.
2）[Adjust
[Adjust[Adjust
[Adjust･
･･
･Check]
Check]Check]
Check] Parallax
Tolerance
ToleranceTolerance
Tolerance：
：：
：Left & Right less than 1°
Left & Right less than 1° Left & Right less than 1°
Left & Right less than 1°
Horizontal
Horizontal Horizontal
Horizontal
less than 1° 50´
less than 1° 50´ less than 1° 50´
less than 1° 50´
Horizontal Parallax can be adjusted by M16 x2.
Apply screw lock onto M16.
3）[Adjust]
[Adjust][Adjust]
[Adjust] View finder focus.
Adjusting washer (M22-000A～I).
Tolerance
ToleranceTolerance
Tolerance：
：：
：0
00
0±
±±
±0.04 mm
0.04 mm0.04 mm
0.04 mm
(Center
(Center (Center
(Center φ
φφ
φ10mm)
10mm)10mm)
10mm)
0
00
0±
±±
±0.07 m
0.07 m0.07 m
0.07 mm
mm
m
(Other than center)
(Other than center)(Other than center)
(Other than center)
4).Make sure that dust, hair and stain should not be observed on
focus screen and on the Penta prism.
S364 0-S300
To Next Page
Loading...
