Need help?Do you have a question about the Philips SpeechMike and is the answer not in the manual?
General| Brand | Philips |
|---|---|
| Model | SpeechMike |
| Category | Barcode Reader |
| Language | English |
Resets the scanner to factory default settings by scanning a specific barcode.
Lists the factory default values for all configurable scanner parameters.
Allows selection of the scanner's decode beep volume using provided barcodes.
Enables selection of the scanner's decode beep frequency or tone.
Adjusts the high beeper tone frequency in 10 Hz increments from 1220 Hz to 3770 Hz.
Configures the transmission of a "NR" message for failed barcode scans.
Controls the ability of the scanner to decode parameter barcodes for configuration.
Sets decode security levels for linear barcodes based on quality (four levels available).
Requires barcodes to be scanned in both forward and reverse directions for decoding.
Enables or disables the decoding of UPC-A barcodes.
Enables or disables the decoding of UPC-E barcodes.
Enables or disables the decoding of UPC-E1 barcodes.
Enables or disables the decoding of EAN-8 barcodes.
Enables or disables the decoding of EAN-13 barcodes.
Enables or disables the decoding of Bookland EAN barcodes.
Configures how the scanner handles supplemental characters for UPC/EAN barcodes.
Sets the number of times a symbol without supplementals is decoded before transmission.
Enables supplemental identification for EAN-13 barcodes starting with '378' or '379'.
Enables supplemental identification for EAN-13 barcodes starting with '978'.
Enables supplemental identification for EAN-13 barcodes with specific prefixes.
Controls whether the UPC-A check digit is transmitted with the barcode data.
Controls whether the UPC-E check digit is transmitted with the barcode data.
Controls whether the UPC-E1 check digit is transmitted with the barcode data.
Configures transmission of system character and country code for UPC-A barcodes.
Configures transmission of system character and country code for UPC-E barcodes.
Configures transmission of system character and country code for UPC-E1 barcodes.
Converts UPC-E decoded data to UPC-A format before transmission.
Converts UPC-E1 decoded data to UPC-A format before transmission.
Adds five leading zeros to EAN-8 symbols to match EAN-13 format.
Labels extended EAN-8 symbols as EAN-13 or EAN-8.
Sets decode security levels for UPC/EAN barcodes based on quality.
Enables or disables the decoding of UCC Coupon Extended Codes.
Enables or disables the decoding of Code 128 barcodes.
Enables or disables the decoding of UCC/EAN-128 barcodes.
Enables or disables the decoding of ISBT 128 barcodes.
Specifies length settings for Code 128 barcodes.
Enables or disables the decoding of Code 39 barcodes.
Enables or disables the decoding of Trioptic Code 39 barcodes.
Enables or disables the conversion of Code 39 to Code 32 (Italian Pharma Code).
Adds a prefix character "A" to all Code 32 barcodes.
Sets length restrictions for decoding Code 39 barcodes.
Verifies the integrity of Code 39 symbols using check digits.
Controls whether the Code 39 check digit is transmitted with the barcode data.
Enables or disables encoding of the full ASCII character set in Code 39.
Enables or disables the decoding of Code 93 barcodes.
Sets length restrictions for decoding Code 93 barcodes.
Enables or disables the decoding of Code 11 barcodes.
Sets length restrictions for decoding Code 11 barcodes.
Verifies the integrity of Code 11 symbols using check digits.
Controls whether Code 11 check digits are transmitted with the data.
Enables or disables the decoding of Interleaved 2 of 5 barcodes.
Sets length restrictions for decoding Interleaved 2 of 5 barcodes.
Verifies the integrity of I 2 of 5 symbols using a specified algorithm.
Controls whether the I 2 of 5 check digit is transmitted with the data.
Converts 14-character I 2 of 5 codes into EAN-13 format.
Enables or disables the decoding of Discrete 2 of 5 barcodes.
Sets length restrictions for decoding Discrete 2 of 5 barcodes.
Enables or disables the decoding of Chinese 2 of 5 barcodes.
Enables or disables the decoding of Codabar barcodes.
Sets length restrictions for decoding Codabar barcodes.
Modifies Codabar symbols by inserting spaces and stripping characters.
Strips start and stop characters from decoded Codabar symbols.
Enables or disables the decoding of MSI Plessey barcodes.
Sets length restrictions for decoding MSI Plessey barcodes.
Configures the number of check digits for MSI Plessey barcodes.
Controls whether the MSI check digit is transmitted with the data.
Selects the algorithm for verifying two MSI check digits.
Enables or disables the decoding of RSS-14 barcodes.
Enables or disables the decoding of RSS-Limited barcodes.
Enables or disables the decoding of RSS-Expanded barcodes.
Inserts a symbol-specific identifier before the decoded data.
Inserts an AIM-standard identifier before the decoded data.
Lists code characters used in AIM Code Identifiers.
Lists modifier characters used in AIM Code Identifiers.
To Next Page