What to do if the effects don’t work on Pioneer SVM-1000?
If the effects aren’t working on your Pioneer Music Mixer, the effect channel selector (CH SELECT) setting may be incorrect; correctly select the channel on which you wish to apply effects. Also, the effect parameter 2 dial (LEVEL/DEPTH) may be set to [MIN]; adjust the effect parameter 2 dial (LEVEL/ DEPTH).
What to do if BPM can’t be measured on Pioneer Mixer?
If the BPM can’t be measured or the measured BPM value is incorrect on your Pioneer Mixer, adjust the AUDIO TRIM dial so that the input level approaches 0 dB on the channel level indicator, because the input level may be too high or too low. If that doesn't work, strike the TAP button to set BPM manually, as BPM may not be correctly measurable with some tracks.
What to do if there is no sound from my Pioneer Mixer?
If there is no sound or the sound volume is too low on your Pioneer Mixer, ensure the AUDIO INPUT switch is correctly set to the currently playing component. Check that all connection cables are properly connected and clean any dirt from connectors or plugs. Also, verify the rear panel MASTER ATT. switch setting and adjust if necessary.
Why effects don’t work on Pioneer Mixer?
If the effects aren’t working on your Pioneer Mixer, make sure the effect channel selector (CH SELECT) is correctly set to the channel on which you wish to apply effects. Also, adjust the effect parameter 2 dial (LEVEL/DEPTH), because it may be set to [MIN].
What to do if there is no sound or low sound from Pioneer Mixer?
If there is no sound or the sound volume is too low on your Pioneer Mixer, ensure the AUDIO INPUT switch is correctly set to the currently playing component. Check that all connection cables are properly connected and not disconnected. Clean any dirt from connectors or plugs before connecting them. Also, verify the rear panel MASTER ATT. switch setting and adjust it if necessary.
Why is the sound distorted on my Pioneer Mixer?
If the sound from your Pioneer Mixer is distorted, adjust the AUDIO MASTER LEVEL dial or the rear panel MASTER ATT. switch, because the audio master output level may be too high. Also, adjust the AUDIO TRIM dial, ensuring the input level approaches 0 dB on the channel level indicator, as the input level may also be too high.
How to fix fader start not working on Pioneer Mixer with DVD/CD player?
If you can't perform a fader start with your DVD/CD player on the Pioneer Mixer, ensure the FADER START button is set to ON. Also, check that the rear panel CONTROL connector is connected to the DVD/CD player with a control cable, and that both the CONTROL connectors and analog input connectors are connected.
What to do if there is no video image or the image is disrupted on Pioneer Mixer?
If you are not getting any video image, or the image is disrupted on your Pioneer Mixer, make sure the VIDEO INPUT switch is correctly set to select the currently playing component. Ensure all connection cables are properly connected and not disconnected, and clean any dirt from connectors or plugs. Adjust trim controls properly. Verify that the signal format of the input video source matches the system setting selected during hardware setup. Also, confirm that the TV monitor’s video signal format matches the system setting selected during hardware setup, and that the TV monitor’s input selector is set to the type of input connected to the unit. Finally, ensure the TV monitor’s component setting is set to 525i (interlaced).
How to troubleshoot no power on a Pioneer Mixer?
If your Pioneer Mixer is not powering on, ensure that the power cord is properly connected to a power outlet.
How to get microphone sound from BOOTH output on Pioneer Mixer?
If you are not getting any microphone sound from the BOOTH output on your Pioneer Mixer, ensure that the OUTPUT TO BOOTH MONITOR is set to ON.
General| Brand | Pioneer |
|---|---|
| Model | SVM-1000 |
| Category | Music Mixer |
| Language | English |
Setting stereo/monaural output, adjusting microphone input, and booth monitor volume.
Adjusting headphone levels/balance and selecting fader response curves.
Operating the video cross fader for effects and using the channel monitor to control video output.
Switching channels instantly and understanding various video mix effects.
Editing text content, font, color, size, and justification for TEXT effects.
Toggling the visibility of the master monitor display on the LCD screen.
Setting up JPEG playback modes and loading files from USB/SD cards.
Assigning JPEG images to channels or creating slide shows.
To Next Page
