Why my Pitco MG14S-C/MFD Fryer computer does not come on?
If the Pitco Fryer computer isn't turning on and nothing is showing on the display, it could be due to a few reasons: * The main circuit breaker might be off. Locate the correct circuit breaker and cycle it OFF and then ON again. * The fryer fuse might be blown. Check the fuse and replace it if necessary. * There could be an issue with the transformer. Check the transformer.
Why won't my Pitco MG14S-C/MFD computer turn on?
If the computer on your Pitco Fryer isn't turning on and nothing is showing on the display, there could be a few reasons. First, check if the main circuit breaker is turned off; if it is, locate it and turn it OFF, then back ON again. Also, the fryer fuse might be blown, so check it and replace it if necessary. Finally, the transformer may need to be checked.
What to do if the Pitco MG14S-C/MFD computer heat light is on but burners do not?
If the heat light is on but the burners aren't igniting, the high limit switch may have tripped due to hot oil. Allow the oil to cool down, which will reset the high limit switch automatically. Then, turn the Pitco Fryer computer off and back on to reset it.
What to do if my Pitco MG14S-C/MFD shows "IGNITION" "FAILURE"?
If your Pitco Fryer's computer displays an "IGNITION" "FAILURE" message while the heat light is on, several components could be the cause. Check the Heat Demand Relay, F2 Fuse, Blower, Pressure Switch, Gas Valve, Ignition Module(s), and Gas Valve Relay (Full Vat Only). Replace any of these as needed. Also, the Hi Limit may be tripped or defective; in this case, allow the oil to cool, which will reset the Hi Limit. Then, turn the computer OFF and back ON again. Replace the Hi Limit if needed.
Why is there no spark in my Pitco Fryer, but the blower is running?
If you hear no spark but the blower is running in your Pitco Fryer, the issue might stem from several components. Check the Heat Demand Relay, Ignition Control Module, and Spark Ignitor. Replace any of these components as needed.
What to do if my Pitco MG14S-C/MFD burner comes on for a short time?
If the burner on your Pitco Fryer comes on for only a short time and doesn't stay on, the issue might be with the Flame Sensor, Ignition Control Module, or Gas Valve. Check each of these and replace them as needed.
What to do if I hear a spark but the blower isn't running on my Pitco MG14S-C/MFD Fryer?
If you hear a spark but the blower isn't running on your Pitco Fryer, the problem could be due to a blown F2 fuse, the blower itself, or the Heat Demand Relay. Check and replace the F2 fuse if needed. Also, inspect and replace the blower or Heat Demand Relay if necessary.
What to do if my Pitco MG14S-C/MFD Fryer computer shows "OFF" and cannot be turned "ON"?
If your Pitco Fryer computer displays "OFF" and cannot be turned "ON", try switching the circuit breaker OFF and then ON again to reset the computer. If this doesn't fix the problem, the computer may need to be replaced.
What to do if I hear a spark and the blower is running but the main burners don't run on my Pitco MG14S-C/MFD?
If you hear a spark and the blower is running, but the main burners do not ignite on your Pitco Fryer, the issue could be with the Ignition Control Module, Gas Valve Relay (Full Vat Only), a bad Pressure Switch, a tripped or defective Hi limit, or the Gas Valve itself. Check each of these components and replace them as needed. For a tripped or defective Hi limit, allow the oil to cool to reset it, and then turn the computer off and back on. Replace the Hi limit if necessary.
Why is the heat light on but the burners don't ignite on my Pitco MG14S-C/MFD Fryer?
If the heat light is on but the burners aren't igniting on your Pitco Fryer, the Hi Limit might be tripped if the oil is hot. Let the oil cool down so the Hi Limit can reset itself. Then, turn the computer OFF and back ON to reset it.
To Next Page
General
