What causes delayed ignition of burner(s) in Procom MN100TPA-B Heater?
Delayed ignition of the burner(s) in your Procom Heater can be caused by manifold pressure that is too low, so contact your local gas supplier. Another cause can be a clogged burner orifice, in which case you should clean or replace the burner orifice.
Why does my Procom MN100TPA-B shut off in use (ODS operates)?
If your Procom Heater shuts off during use and the ODS operates, it could be due to insufficient fresh air, so open a window and/or door for ventilation. Low line pressure could also be the cause, so contact your local gas supplier. Another possibility is that the ODS/pilot is partially clogged, so clean the ODS/pilot.
Why does my Procom MN100TPA-B produce a clicking/ticking noise just after burner is lit or shut off?
If your Procom Heater produces a clicking or ticking noise just after the burner is lit or shut off, it is likely due to metal expanding while heating or contracting while cooling. This is common with most heaters. If the noise is excessive, contact a qualified service technician.
Why is there white powder residue forming within burner box of my Procom MN100TPA-B Heater?
If you notice white powder residue forming within the burner box or on adjacent walls or furniture, it is likely due to vapors from furniture polish, wax, carpet cleaners, etc., turning into white powder residue when heated. Turn off the heater when using these products.
Why does my Procom Heater have slight smoke or odor during initial operation?
If you notice a slight smoke or odor during the initial operation of your Procom Heater, it is likely due to residues from the manufacturing process. This problem will stop after a few hours of operation.
Read manual carefully, keep area clear of flammables, and follow all instructions.
Details CO poisoning risks, symptoms, and vulnerable individuals.
Advises on accessory use, child supervision, clearances, hot surfaces, and flammables.
Lists technical specifications like model, ignition, gas type, BTU, pressure, weight, and dimensions.
Identifies key components of the vent-free gas heater via a diagram.
Defines a qualified agency and outlines responsibilities for installation and servicing.
Describes the ODS safety shutoff and piezo ignition systems.
Explains the thermostat for comfort and potential cost savings.
Emphasizes following local codes and national standards like NFPA 54.
Instructions for removing the heater from packaging and checking for shipping damage.
Provides steps to manage water vapor issues from unvented heaters.
Explains the need for fresh air for proper combustion and ventilation in energy-efficient homes.
Details methods for providing ventilation air from adjoining rooms.
Explains methods for providing ventilation air directly from outdoors.
Provides notice on supplemental heat use and cautions for garage installation.
Warns against installing near flammables and specifies minimum clearances from walls, floor, and ceiling.
Advises on heater placement and provides steps for removing the front panel.
Details methods for attaching the mounting bracket to walls (studs or anchors).
Provides detailed steps for attaching the bracket using wall studs or anchors.
Guides on hanging the heater onto the bracket and installing wall spacers.
Continues wall mounting steps, including using anchors and screws.
Instructions for attaching the base stand feet to the heater.
Outlines requirements for qualified technicians, pipe types, and connection sizes.
Details gas pressure checks for natural and propane gas, and regulator requirements.
Illustrates the gas connection setup for natural gas supply.
Illustrates the external regulator setup for propane gas supply.
Provides warnings and methods for leak testing gas connections using leak detection fluid.
Details procedures for pressure testing the gas supply piping system.
Outlines steps for pressure testing the heater's gas connections after installation.
Crucial safety warnings and actions before attempting to light the heater.
Step-by-step instructions for handling gas leaks.
Detailed procedure for lighting the pilot and main burner on thermostat models.
Instructions on setting the control knob for desired heating levels.
Procedures for turning the heater completely off or just the main burner.
Steps for lighting the pilot using a match if the ignitor fails.
How to identify correct and incorrect pilot flame patterns.
How to identify correct and incorrect burner flame patterns, including yellow tipping.
Warnings about servicing, cleaning, and general maintenance procedures.
Instructions for cleaning main burner holes, injector holder, pilot air inlet, and air passageways.
Instructions for cleaning the heater cabinet's exterior.
Critical warnings and procedures for dealing with gas odors or leaks.
Troubleshooting for ignitor not sparking or pilot not igniting after sparking.
Troubleshooting for pilot going out after release and burner ignition failures.
Addresses burner backfiring, plaque not glowing, and high yellow flames.
Explains causes and solutions for gas odors, smoke, noise, and residue during operation.
Troubleshooting for heater shutoffs (ODS) and moisture/condensation issues.
Lists part numbers and descriptions for replaceable components of the heater.
Information on obtaining replacement parts under warranty and those not covered.
Details about purchasing optional accessories and equipment shutoff valves.
Hints for troubleshooting when gas pressure is too low.
Encourages product registration and keeping warranty information for verification.
Details new product warranty, reconditioned product warranty, owner duties, and exclusions.
To Next Page
General
