ProLights UNICO - Wireless Control Setting; Fixture Setting; Lamp Setting

21
UNICO
3.10 WIRELESS CONTROL SETTING (For the unit with wireless receiver built-in only)
• Press MENU to select [DMX FUNCTIONS] and press ENTER button to conrm.
• Select [WDMX Setting], press ENTER button to conrm.
• Set the desired parameter using the UP/DOWN button and press the ENTER button to conrm the set-
ting.
- [Active] - Wireless control. Select [Active], press ENTER button to conrm, use UP/DOWN button to
select [Yes] (wireless control available) or [No] (wireless control unavailable), press ENTER button to
store.
- [Retransmit] - Select [Retransmit], press ENTER button to conrm, use UP/DOWN button to select [Yes]
or [No], press ENTER button to store.
- [Reset Memory] - Refuse wireless signal. Select [Reset Memory], press ENTER button to conrm, use UP/
DOWN button to select [Yes] (refuse wireless signal) or [No], press ENTER button to store.
• Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.
3.11 FIXTURE SETTING
It is possible to change the device parameter values in the following way.
• Press MENU to select [FIXTURE SETTING] and press ENTER button to conrm.
• Set the desired parameter using the UP/DOWN button and press the ENTER button to conrm the set-
ting.
- [Pan Inverse] - Used for reversing Pan movement. Select [Pan Inverse], press ENTER button to conrm,
present mode will blink on the display, use UP/DOWN button to select [No] (normal) or [Yes] (pan
inverse), press ENTER button to store.
- [Tilt Inverse] - Used for reversing tilt movement. Select [Tilt Inverse], press ENTER button to conrm,
present mode will blink on the display, use UP/DOWN button to select [No] (normal) or [Yes] (tilt
inverse), press ENTER button to store.
- [P/T Feedback] - Select [P/T Feedback], press ENTER button to conrm, present mode will blink on the
display, press UP/DOWN button to select [No] (Pan or tilt’s position will not feedback while out of
step) or [Yes] (Feedback while pan/tilt out of step), press ENTER button to store.
- [BL.O. P/T Moving] - Blackout while Pan/Tilt moving. Select [BL.O. P/T Moving] press ENTER button to con-
rm, present mode will blink on the display, use UP/DOWN button to select [No] (normal while pan/
tilt moving) or [Yes] (blackout while pan/tilt moving), press ENTER button to store.
- [BI.o. Color Change] - Blackout while change color. Select [BI.o. Color Change] press ENTER button to
conrm, present mode will blink on the display, use UP/DOWN button to select [No] (normal while
change color) or [Yes] (blackout while change color), press ENTER button to store.
- [BI.o. Gobo Change] - Blackout while change gobo. Select [BI.o. Gobo Change] press ENTER button to
conrm, present mode will blink on the display, use UP/DOWN button to select [No] (normal while
changing gobo) or [Yes] (blackout while changing gobo), press ENTER button to store.
• Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.
3.12 LAMP SETTINGS
It is possible to change the device parameter values in the following way:
• Press MENU to select [LAMP SETTING] and press ENTER button to conrm.
• Set the desired parameter using the UP/DOWN button and press the ENTER button to conrm the set-
ting.
- [On/O] - Turn on/o the lamp. Select [On/O], press ENTER button to conrm, present mode will blink
on the display, use UP/DOWN button to select [On] (lamp on) or [O] (lamp o), press ENTER button
to store.
- [State/Power On] - Lamp state while power on. Select [State/Power On], press ENTER button to conrm,