ProLights UNICO - Display Setting; Fixture Test

UNICO
22
present mode will blink on the display, use UP/DOWN button to select [On] (Lamp on while power
on) or [O] (Lamp o while power on), press ENTER button to store.
- [O Via DMX] - Turn o the unit via DMX controller. Select [O Via DMX] press ENTER button to conrm,
present mode will blink on the display, use UP/DOWN button to select [Yes] (turn o the unit via
DMX controller available) or [No] (turn o the unit via DMX controller impracticable), press ENTER
button to store.
- [On If DMX On] - Lamp turns on when DMX signal is detected. Select [On If DMX] press ENTER button to
conrm, present mode will blink on the display, use UP/DOWN button to select [Yes] (Lamp turns
on when DMX signal is detected) or [No] (keep the present state), press ENTER button to store (If the
lamp is o via DMX signal, you can reconnect the DMX controller to make the lamp on).
- [O If DMX O] - Lamp turns o when DMX signal is cut o. Select [O If DMX O] press ENTER button to
conrm, present mode will blink on the display, use UP/DOWN button to select [Yes] (Lamp turns o
when DMX signal is cut o), press ENTER button to store.
- [Ignition Delay] - Delay time between power on and lamp on. Select [Ignition Delay] press ENTER button
to conrm, present mode will blink on the display, use UP/DOWN button to adjust the delay time
from 0s to 255s, press ENTER button to store.
- [Low Power Delay] - Delay time between power on and lamp on. Select [Low Power Delay] press ENTER
button to conrm, present mode will blink on the display, use UP/DOWN button to adjust the delay
time from 0s to 255s, press ENTER button to store.
• Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.
3.13 DISPLAY SETTING
• Enter MENU mode, select [DISPLAY SETTING], press ENTER button to conrm.
• Set the desired parameter using the UP/DOWN button and press the ENTER button to conrm the set-
ting.
- [Display Inverse] - Used for reversing display. Select [Display Inverse], press ENTER button to conrm,
present mode will blink on the display, use UP/DOWN button to select [No] (normal display) or [Yes]
(inverse display), press ENTER button to store.
- [Backlight Auto O] - Select [Backlight Auto O], press ENTER button to conrm, present mode will blink
on the display, use UP/DOWN button to select [No] (display always on) or [Yes] (display goes o one
minute after exiting menu mode), press ENTER button to store.
- [Backlight Intensity] - Select [Backlight Intensity], press ENTER button to conrm, present mode will blink
on the display, use UP/DOWN button to adjust backlight intensity from 1 (dark) to 10 (bright), press
ENTER button to store.
- [Contrast Ratio] - Select [Contrast Ratio], press ENTER button to conrm, present mode will blink on the
display, use UP/DOWN button to adjust the intensity ratio from 1 (dark) to 30 (bright), press ENTER
button to store.
- [Temperature Unit] - Select [Temperature Unit], press ENTER button to conrm, present mode will blink on
the display, use UP/DOWN button to select °C or °F, press ENTER button to store.
- [Display Warning] - Select [Display Warning], press ENTER button to conrm, present mode will blink on
the display, use UP/DOWN button to select [No] (Normal) or [Yes] (display will show the error warning
when the unit went wrong).
• Press MENU button back to the last menu or let the unit idle one minute to exit menu mode.
3.14 FIXTURE TEST
Auto Test
Allow checking the proper functioning of the unit. Start the automatic test in the following way: