What to do if my Pyronix EURO 46 APP shows 'Input (xx) Wirles Poll Fail'?
If the Pyronix Control Panel displays 'Input (xx) Wirles Poll Fail', test the signal strength and battery status for each wireless device, especially the one corresponding to the input named in the fault message.
How to fix 'WLs Supervn Fault' on my Pyronix EURO 46 APP Control Panel?
If the Pyronix Control Panel displays 'WLs Supervn Fault', test the signal strength and battery of each of the wireless devices.
Why does my Pyronix EURO 46 APP Control Panel show 'BATTERY FAULT'?
If the Pyronix Control Panel shows a 'BATTERY FAULT' message, especially right after a mains failure, it is likely due to the battery recharging. This indication is normal during the recharge process.
How do I resolve 'Engineer Access Denied' on my Pyronix EURO 46 APP?
If your Pyronix Control Panel displays 'Engineer Access Denied', ensure that ALL areas are unset, using suitable user codes/tags at the appropriate keypads/readers.
What to do if my Pyronix EURO 46 APP shows 'DEVICE FAIL'?
If the Pyronix Control Panel displays 'DEVICE FAIL xxx xxx = OM xxx = ZEM xxx = Kpd xxx = Trd xxx = Pnl', first, identify the specific device that is failing. Then: 1. Check that the device is addressed correctly to match the programming. 2. Inspect the connections at the device and the cabling to it. 3. If the above steps are correct, reboot the device, followed by a reboot of the End Station.
How to fix 'Authorisation Required' error on Pyronix EURO 46 APP Control Panel?
If the Pyronix Control Panel displays ‘Authorisation Required’, the ‘Allow Engineer Menu’ option needs to be enabled by the master manager.
What should I do if there is an 'Alarm during the setting' on my Pyronix Control Panel?
If your Pyronix Control Panel displays 'Alarm during the setting', you should leave the premises within the fail to set time. Alternatively, you can increase the fail to set time in the 'timers' settings or disable this feature in the system options.
What does 'BAT LOAD FAIL' mean on my Pyronix Control Panel, and how do I fix it?
If your Pyronix Control Panel shows 'BAT LOAD FAIL', and the option is selected, it indicates that the battery is either uncharged or its capacity is below the specified level. In this case, the battery may need to be replaced.
What to do if my Pyronix EURO 46 APP says 'Unable To Set'?
If the Pyronix Control Panel displays 'Unable To Set', correct the problem if an input is open, or call an engineer.
What does 'LOW VOLTS' mean on my Pyronix EURO 46 APP?
If your Pyronix Control Panel displays 'LOW VOLTS', it means the battery voltage has dropped below the normal 'battery fault' level during a mains failure.
General| Zones | 46 |
|---|---|
| Keypads | 4 |
| Power Supply | 230V AC |
| Operating Temperature | -10°C to +40°C |
| Type | Hybrid |
| Communication | GPRS, PSTN, IP |
| Connectivity | Ethernet, GSM |
| Mobile App | Yes |
| Compatibility | Pyronix wireless devices |
| Battery Backup | 12V |
High security wireless alarm system with two-way communication.
Preserves device battery life and notifies of replacement needs.
Utilizes 128-bit encryption and jamming detection for enhanced security.
Explains keyfob LEDs and programmable functions for system control.
Allows control of external devices like gates and lights via the system.
Real-time notifications for events via the HomeControl+ app or SMS.
Details four methods for setting/unsetting: keypad, tag, keyfob, app.
Illustrates how to navigate the panel menus using keypad buttons.
Explains how to respond to menu questions to navigate options.
Activates a chime sound for door openings detected by magnetic contacts.
Describes how to trigger a Hold-Up alarm using specific keypad buttons.
Assigns specific functions to the four keyfob buttons.
Method to prevent accidental keyfob button presses.
Allows immediate system setting after initiating the exit timer.
Covers setting via keypad, tag, app, and keyfob.
Covers unsetting via keypad, tag, app, and keyfob.
Detailed steps for setting/unsetting using a tag and reader LEDs.
Explains using tag readers solely for door access without arming/disarming.
How to use the wireless arming station for system arming/disarming.
Manages external outputs directly from the arming station.
Using SMS commands to set or unset specific system areas.
Commands to exclude inputs during system setting via SMS.
Retrieves system status, area status, and fault information via SMS.
Controls user automation outputs (ON/OFF) using SMS commands.
Updates the system's registered mobile number for SMS using a command.
Configure panel date, time, and daylight saving adjustments.
Activate or deactivate user automation outputs for remote control.
Program user codes, tags, and learn keyfobs for system access.
Access and view system operational history, including alarms and access events.
Steps to access the Master Manager menu using the default code.
Detailed guide for setting the panel's date and time.
Controls the activation/deactivation of user-defined automation outputs.
Allows specific inputs to be omitted during the current setting period.
Process for adding new users, setting their type, and areas.
Options for modifying or removing existing user codes.
Procedure to update the primary Master Manager access code.
Steps to enroll and configure proximity tags for system access.
Configures tag behavior for flexible area selection during system setting.
Process to add and program keyfobs for specific button actions.
Accesses and displays the system's event history from the panel log.
Accesses and displays user access events from the access log.
Sets up app usage, system ID, and password for normal security level.
Manages the 'Always Poll Cloud' setting for continuous app data synchronization.
Sets up app for high security, including complex password generation.
Method to deliver the generated app password key via SMS.
Guides through connecting the alarm panel to a Wi-Fi network.
Manages phone numbers for SMS alarm notifications.
Instructions for testing system detectors by walking through areas.
How to perform a test of the system's siren and strobe.
Controls whether engineer menu requires specific authorization.
Prevents remote setting/unsetting via UDL software.
Prevents remote panel access for uploads and downloads via UDL.
Plays various sounds to demonstrate different system alerts and tones.
Steps to exit the Master Manager menu and return to normal operation.
Section for recording installer details and installation specifics.
Lists and describes wired inputs, their areas, and names.
Lists and describes wireless inputs, their areas, and names.
Details inputs associated with specific keypads and their areas.
Table for associating users with their access credentials.
Configuration details for wired outputs like Bell and Strobe O/P.
Details for user-defined and ZEM module outputs, including timing and actions.
Instructions on proper disposal of electrical products and batteries.
Outlines the warranty terms, conditions, and limitations for Pyronix products.
To Next Page
