Raymarine RAY73 - GNSS (GPS) Location Requirements

5.
7SharedBrightness
Y oucansetupSharedBrightnessgroupswhichenables
simultaneousbrightnessadjustmentofallunitsthatare
partofthesamegroup.
ThefollowingproductsarecompatiblewithShared
Brightness:
•LightHouse™3MFDsusingsoftwareversion3.4or
greater.
•LightHouse™orLightHouse™2poweredMFDs.
•SeaTalkng®InstrumentdisplaysandPilotcontrollers.
•SeaTalkng®VHFDSCRadios.
AnyadjustmentstotheSharedBrightnesslevelwillbe
reflectedonallunitsassignedtothesamegroup.
LightHouse™/
LightHouse™2MFD
Instrumentdisplay/
Pilotcontroller
VHFDSCR adioLightHouse™3V3.4
Multiplebrightnessgroupscanbeconfigured.These
groupscouldbeusedtoreflectthephysicallocationof
unitsonyourvessel.Fore xample,theunitsatyourhelm
canbesettoonegroup,andtheunitsontheflybridge
canbesettoadifferentgroup.
SharedBrightnessrequires:
•allunitstobecompatiblewiththeSharedBrightness
function(seelistofcompatibleunitsabove).
•the
SharedbrightnesssettingsettoOnforallunits
inthebrightnessgroup
.
•unitstobeassignedtoNetworkGroups.
•allthedisplaysinthatgrouptobesynchronized.
EnablingSharedBrightness
Fromthe
DisplaySet-upmenu:( Menu>Set-up>
DisplaySet-up).
1.Select SharedBrightness.
2.Select
SharedBrightnessagaintoenableShared
Brightness.
IfSharedBrightnessisalreadyenabledthen
selectingthismenuitemwilldisableShared
Brightness.
3.Select Group.
4.Selectthegroupthatyouwanttoassigntheradioto.
AdjustingtheBrightnesssettingwillnowchangethe
brightnessofallproductsassignedtothatgroup.
5.8Initialstartup
Unlessyourradiohasbeenpre-programmed;thefirst
timeyoupower-upyourradioyouwillberequestedto
selectcertainoptions.WiththeexceptionofyourMMSI
andATISID,youwillalsoberequestedtoenterthese
optionsafterafactoryreset.
Afteracknowledgingthestartupscreen,unless
previouslysetyouwillbepromptedtomakethe
followingselections:
1.Languageselection—See5.10Selectinga
languageforavailablelanguages.
2.TurnonAISreception(Ray70andRay91only)—
Enablesthebuilt-inAISreceiver.Thisstepisonly
applicabletoradioswithabuilt-inAISreceiver.
See5.11SwitchingontheAISreceiverformore
information.
3.Selectnetworktype—Selectswhichconnectionto
transmitAISandDSCinformationon,toconnected
equipment.ThisstepisonlyapplicableiftheAIS
receiverwasturnedoninthepreviousstep.See
5.12Selectinganetworktypeforavailableoptions.
4.EnterMMSInumber—RequiredtoenableDSC
functions.Thisoptionisnotrequiredafterafactory
reset,oriftheradiohasbeenpre-programedin
MARCOM-Cmode,orhasATISenabled.See5.13
EnteringanMMSInumberformoreinformation.If
notalreadyselectedyouwillalsobepromptedto
selectyournetworktype.
5.EnterATISID—Requiredwhentheradiowillbe
usedintheinlandwaterwaysofEurope.Thisstepis
onlyapplicableiftheradiohasbeenpre-programed
inMARCOM-Cmode.See5.14EnteringanATISID
formoreinformation.
6.Frequencybandselection—Setstherelevant
channelsforyourregion.Thisstepisnotapplicable
iftheradiohasbeenpre-programedinMARCOM-C
mode.See5.15Changingtheradioregionformore
information.
Gettingstarted
47
81381-1-Ray53_63_73_Install_and_Ops_PRINT.pdf 47 6/13/2018 2:30:12 PM