Renfert Silent TS2 - Error codes

- 17 -
Error Possible Cause Corrective Action
Extractor starts,
although a connected
device is not being
used.
Start-up threshold of one suction
hoses is too low.
Check, which suction hose is open, the relevant letter
will be indicated in the display.
Adjust the start-up threshold of the suction hose
(Chapter 5.3.4).
Extractor fails to stop
when a connected
device is switched off
The dust generating device is not
plugged in to the coupler socket on
the extractor and the suction hose
button is switched on.
Start-up threshold is too low
Shut-off delay is too long.
Switch the suction hose button on the extractor off,
and connect the dust generating device to the coupler
socket on the extractor (Chapter 4.7).
Adjust start-up threshold (Chapter 5.3.4)
Set shorter shut-off delay (Chapter 5.3.5).
No satisfactory setting
for the automatic
start-up feature can be
adjusted.
Some older hand pieces do not
JHQHUDWHDVXI¿FLHQWO\VWURQJVLJQDO
for the automatic start-up feature.
Switch to higher revs per minute (e.g. 10,000 rpm.)
3DQHOVFRYHULQJWKH¿QH
SDUWLFOH¿OWHUDQGWKH
GXVWGUDZHUDUHGLI¿FXOW
to open.
Lock bolts are dirty. Clean lock bolts and lubricate them slightly if
necessary.
The extraction force is
not readjusted when a
second suction hose is
switched on or off
The automatic extraction force
readjustment is deactivated.
Activate the automatic extraction force readjustment
(See chapter 5.2.2).
The display indicates
“OFF” above the button
(41)
The automatic extraction force
readjustment is deactivated.
Activate the automatic extraction force readjustment if
required (See chapter 5.2.2).
There is no audible
signal.
The audible signal is deactivated. Activate audible signal (Chapter 5.3.2)
Pinch valves close /
open slowly
7KH¿OWHULQWKHFRPSUHVVHGDLU
connection is blocked
&KDQJHWKH¿OWHULQWKHFRPSUHVVHGDLUFRQQHFWLRQ
(see chapter 6.2.4).
7.1 Error codes
,IWKHIROORZLQJHUURUFRGHDSSHDUVGXULQJRSHUDWLRQRUVHOIGLDJQRVLVSOHDVHFRQWLQXHDVIROORZV
 Switch device off
 Deal with the fault as described in the table
 Switch the device back on
For all other error codes, switch the unit off and then back on again.
,IWKHHUURUFRGHLVUHSHDWHGO\LQGLFDWHG
 Make a note of the error code.
 Contact the repair service
Error Code Cause / Meaning Corrective Action
Cod01 7KHVHWGXVWEDJ¿OOOHYHOKDVEHHQ
reached.
Change dust bag (Chapter 6.1).
Err01 6XFWLRQÀRZLVEORFNHG
,QVXI¿FLHQWFRPSUHVVHGDLUSUHVVXUH
Check the suction hoses for blockages, examine
WKHGXVWEDJ¿OOOHYHODQGFKDQJHLIQHFHVVDU\
6HHFKDSWHUH[DPLQHWKH¿QHSDUWLFOH¿OWHUIRU
contamination, and change if necessary (see chapter
6.2.1).
If the device is supplied with compressed air from
a main laboratory switch together with the air
FRPSUHVVRUWKHQDW¿UVWWKHFRPSUHVVHGDLUZLOOEH
LQVXI¿FLHQWDQGWKHVHOIGLDJQRVLVZLOOLQGLFDWHDIDXOW
6ZLWFKWKHGHYLFH21DWWKH2Q2IIVZLWFK¿J
Err04 Overheated electronics Switch the extractor off and allow cooling. If the
extractor is located in a closed cabinet, make sure
the exhausted air is able to escape (See chapter 4.2).
EN