Why pinch valves close / open slowly on Renfert Silent TS2 Dental equipment?
If the pinch valves on your Renfert Dental equipment are closing or opening slowly, the filter in the compressed air connection may be blocked. Replace the filter in the compressed air connection.
What to do if Renfert Medical Equipment extractor stops suddenly and shows an error code?
If your Renfert Medical Equipment extractor stops suddenly and displays an error code, it means an error has been detected. Refer to the “Error Codes” table in the manual. If the provided instructions don't resolve the issue or the error isn't listed, make sure to note the error code and send the device in for repair, informing the repair service of the specific error code.
Why does Renfert Medical Equipment extractor start even when a connected device is not being used?
If your Renfert Medical Equipment extractor starts even when a connected device isn't in use, the start-up threshold of one of the suction hoses might be too low. Check which suction hose is open as indicated on the display, and then adjust the start-up threshold of that suction hose.
Why does Renfert Medical Equipment extractor fail to stop when a connected device is switched off?
If your Renfert Medical Equipment extractor doesn't stop when a connected device is switched off, it could be because the dust generating device isn't plugged into the coupler socket and the suction hose button is on, the start-up threshold is too low, or the shut-off delay is too long. Try these solutions: * Switch off the suction hose button and connect the dust generating device to the coupler socket. * Adjust the start-up threshold. * Set a shorter shut-off delay.
What to do if Renfert Medical Equipment dust bag full indicator appears shortly after replacing the dust bag?
If the “Dust bag full” indicator on your Renfert Medical Equipment appears shortly after replacing the dust bag, it could be due to a blocked fine particle filter, an obstruction in the suction hose, or a too small cross-section of the dust generating device’s hosting. To resolve this: * Replace the fine particle filter. * Remove any obstructions in the suction hose. * Reset the sensitivity of the “dust bag full” indicator.
Why can't I adjust a satisfactory setting for the automatic start-up feature on my Renfert Silent TS2 Dental equipment?
If you're unable to find a satisfactory setting for the automatic start-up feature on your Renfert Dental equipment, it may be because some older hand pieces do not generate a sufficiently strong signal. Try switching to higher revolutions per minute (e.g., 10,000 rpm).
What to do if the 'Dust bag full' indicator turns on even when the bag is not full in Renfert Dental equipment?
If the “Dust bag full” indicator activates on your Renfert Dental equipment even when the bag isn't full, the sensitivity of the signal may be too low. Increase the value to correct this.
How to fix dust bag over full issue in Renfert Dental equipment?
If the dust bag in your Renfert Dental equipment is registering as over full, it might be because the sensitivity of the “dust bag full“ signal is too large. To resolve this, set a smaller value.
What causes pinch valves close or open slowly on Renfert Medical Equipment?
If the pinch valves on your Renfert Medical Equipment are closing or opening slowly, the filter in the compressed air connection might be blocked. To resolve this, change the filter in the compressed air connection.
Why is the extraction force not readjusted on Renfert Medical Equipment?
If the extraction force isn't readjusting when a second suction hose is switched on or off on your Renfert Medical Equipment, the automatic extraction force readjustment is likely deactivated. To fix this, activate the automatic extraction force readjustment.
Explains warning symbols and their meanings for safe operation and equipment protection.
Defines the device's purpose for extracting dry, non-explosive dust in dental laboratories.
Details prohibited materials and uses to prevent hazards and damage.
Specifies environmental requirements for safe device operation, including temperature and humidity.
Outlines temperature and humidity limits for storing and transporting the unit.
Provides general and specific warnings for safe device usage and potential risks, including electrical hazards.
Defines qualifications required for operating and maintaining the device.
States Renfert GmbH's liability limitations for product misuse or unauthorized modifications.
Provides an overview of the workbench extraction unit for dental laboratories.
Lists different dental laboratory applications suitable for the extraction unit.
Identifies and describes the main parts and controls of the Silent TS2 unit.
Lists all items included in the product package upon purchase.
Details optional accessories available for purchase to enhance the unit's functionality.
Instructions for removing the device and accessories from the packaging.
Guidance on positioning the extraction unit for optimal performance and accessibility.
Information on setting up an external route for extracted air leaving the laboratory.
Steps for safely connecting the device to the power supply.
Instructions for connecting the unit to a compressed air supply for pinch valve operation.
Guide for attaching pre-assembled pinch valves and suction pipes to the unit.
Details how to reconfigure or alter the suction pipe and pinch valve assembly.
Instructions for connecting the suction hose to the unit's extraction point.
Explains how to connect external electrical appliances to the unit's coupler sockets.
Describes the procedure for powering the extractor unit on and off.
Explains how the unit enters and exits stand-by mode.
Details how the extraction process works when a suction hose is opened.
How to adjust and manage the suction power levels of the extractor.
Guide to setting and saving custom extractor configurations and parameters.
How to activate and interpret the self-diagnosis function for device checks.
Instructions for enabling or disabling audible signals for warnings and confirmations.
Explains the indicator for a full dust bag and how to adjust its sensitivity.
How to set the point at which connected appliances activate the suction hose.
Configuration of the time delay between appliance shutdown and suction hose closure.
Step-by-step guide for removing and replacing the dust bag.
Overview of the unit's two-level filter system and general filter maintenance.
Instructions for examining and replacing the fine particle filter.
Guide for replacing the exhaust filter that traps graphite brush particles.
How to examine and replace the filter for the unit's electronics cooling air.
Instructions for changing the filter in the compressed air connection.
Explains the self-diagnosis process and its importance for detecting faults.
Details the overload switches that protect the extractor and how to reset them.
How to reset all custom settings back to the original factory defaults.
Information on where to find order numbers for consumables and spare parts.
Lists specific error codes, their causes, and recommended corrective actions.
Guidelines for properly disposing of used dust bags and filters according to regulations.
Instructions for the authorized recycling and disposal of the entire unit.
General| Type | Dust extraction unit |
|---|---|
| Application | Dental laboratory |
| Supply voltage | 230 V, 50/60 Hz |
| Air pressure | No data available |
| Air consumption | No data available |
| Connection | No data available |
| Power Supply | Mains-operated |
To Next Page
