Need help?Do you have a question about the Ricoh J014 and is the answer not in the manual?
Preparation steps before installing the machine, including environment and location selection.
Specifies minimum computer hardware and software requirements for proper machine operation.
Instructions on how to operate the machine using its control panel keys and menus.
Step-by-step guide for installing the machine, including accessory checks and material removal.
Procedure for correctly installing the ink cartridges into the printer.
Instructions on how to properly load paper into the machine's paper tray.
Final steps to complete the machine installation, including power-on and initial setup.
Guide for installing the USB connection and the necessary printer driver software.
Details on available optional equipment such as paper feed units and bypass trays.
General safety precautions to follow when using the product.
Outlines duties and responsibilities for maintenance and installation.
Safety guidelines for shipping and moving the machine.
Safety precautions related to the machine's power supply and connections.
Precautions regarding the use and replacement of safety devices like fuses.
Safety checks and precautions for the power plug and cord integrity.
Specific safety instructions for handling ink cartridges, including exposure.
Table outlining preventive maintenance tasks and frequency.
Procedures to be performed by a service technician during service calls.
Routine cleaning procedures for specific machine parts like glass and plates.
Precautions and information before starting parts replacement.
Table listing components and their replacement difficulty levels.
Crucial notices related to parts removal, especially critical screws.
Summary of procedures for component removal, listing parts to remove first.
General procedures applicable to multiple components like NIB and duplex unit.
Procedure for replacing the scanner unit, including data backup.
Procedure for removing the rear cover.
Procedure for removing and replacing the flushing unit.
Procedure for removing and replacing the maintenance unit.
Information and procedures related to vertical and horizontal encoder components.
Procedures for replacing various circuit boards like PSU, HVPS, and CTL.
Procedures for replacing motors such as horizontal, vertical, and maintenance.
Procedures for replacing various sensors like encoder, registration, and ink level sensors.
Procedures for cleaning components such as feed rollers, transport belts, and pads.
Instructions for updating the machine's firmware through a PC connection.
Overview of information displayed on the operation panel and menu items.
Information on how to print various status reports like page counter and system summary.
Flowchart detailing the self-diagnostic test procedures for error identification.
List of SC error codes, their levels, causes, and typical errors.
List of jam codes, their meanings, causes, and recommended actions.
List of potential errors occurring during fax communication (RX and TX).
Procedures for adjusting and correcting image quality, including nozzle checks.
Procedure for adjusting the print head position to correct alignment issues.
Procedure for adjusting the print start position for accurate paper alignment.
Procedure for drive cleaning, a last resort for print head issues.
Preliminary information on service modes and accessing them.
Details on accessing and navigating the Service Mode menus.
Tables detailing SP codes for various adjustments and settings.
SP codes for Main Scan and Sub Scan Registration adjustments.
SP codes for calibrating humidity and temperature sensors for duplex printing.
SP codes for configuring charge ID tables for different print head modes.
SP codes for adjusting the print head gap based on DPI settings.
SP codes for adjusting the standard ink coverage amount.
Various SP codes for resetting and restoring machine settings.
Procedures for uploading and downloading printer firmware.
SP codes for checking the status of various machine sensors.
SP codes for displaying current readings from encoder sensors.
SP codes to display various counts related to ink charge.
SP codes to display user print head cleaning counts.
SP codes for air purge/refill counts after ink has run out.
SP codes for automatic cleanings performed between page prints.
SP codes for tracking maintenance operations executed automatically.
SP codes for displaying the current software count for the ink collector unit.
SP codes for the mist counter used in automatic cleaning processes.
Description and functions of soft bit switches for printer operation settings.
Summary of bit switch functions, settings, and their details.
Identification and description of key machine parts, with diagrams.
Information about the machine's circuit boards, including diagrams.
Overview and summary of the machine's electrical components.
Detailed information about the print heads, including specifications and tanks.
Information about ink properties, print heads, and the ink supply system.
Overview of the ink supply system, including cartridges and pumps.
Explanation of the carriage drive system, including motors and belts.
Description of the paper handling mechanisms like feed, transport, and exit.
Explanation of basic machine operations, including power-on initialization.
Overview of the steps involved in the machine's image processing.
Detailed information and operation of the duplex unit.
Description of the optional multi bypass tray for paper feeding.
Description of the optional paper feed unit and its paper handling.
Information and overview of the Automatic Document Feeder.
General technical specifications for ADF, scanner, and printer.
Estimated yields for print cartridges and ink collector unit.
Detailed specifications for print cartridges, including sizes and colors.
Recommended operating and storage environmental conditions.
Specifications for copy, scan, and print operations.
Technical specifications related to the fax functionality.
Specifications for optional equipment like paper feed units and bypass trays.
Table detailing supported paper sizes for various trays and modes.
Basic specifications for the machine's controller unit.
Specifications for USB and Network interfaces.
List of supported software utilities for machine management.
To Next Page
General
