RIDGID EB4424 - Page 25

25
Repair Parts
Parts List For RIDGID Oscillating Edge Belt/Spindle Sander
Model EB44240
RIDGID parts are available on-line at www.ridgidparts.com
Figure 1
Always order by Part Number—Not by Key Number
* Standard Hardware Item - May be purchased locally
† These parts are available where you purchased your sander.
• Any attempt to repair this motor may create a hazard unless repair is done by a qualified service technician. Repair
service is available at your nearest Authorized Service Center.
Key
No.
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
826358
805553-2
822304
†
825808
†
810993-2
825841
825544
805297-9
825523
825548
825844
825842
825537
825852
159572-138
808380-7
825840
826803
159572-186
824604
826783
826469
805641-1
826470
Knob Spindle
Washer 21/64 x 5/8 x 1/32
Drum Sanding 3/4"
Drum Sandpaper
Plate Throat 2"
Belt Sanding 4" x 24"
Screw Set Half Dog 10/32 x 1/2
Adapter Throat Plate
Fan
Screw Flat Hd 1/4-20 x 5/8
Table Rear
Plate Wear
Nut Special Twin 1/4-20
Screw Shoulder 1/4-20
Bracket Table Lock
Knob 1/4-20 x 3/4
Screw Wash/Hd
Ty “T” 10-32 x 3/8
Screw Pan Hd 10-14 x 1/2
Spring Detent
Base
Screw Hex Hd
Ty “T” 1/4-20 x 1
Screw Hex Wash/Hd
Ty “T” 8-32 x 3/8
• Motor Asm
Follower Cam
Ring Retaining 5133-31
Housing
Key
No.
Part No. Description
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
822356
826801
825854
819012
9416630
826347
AC1000
817399-11
37837
825549
825537-1
825543
825524
803309-2
825525
825539-1
SP6001
37836
—
60358
805553-24
822304-1
822304-2
822304-3
825808-1
825808-2
825808-3
805642
Nut Hex Flange Lock 8-32
Enclosure
Cord w/Plug
Foot
Screw Hex Hd Ty “T” 5/16-18 x 1
Switch Locking
† Key Switch
Relay
Wrench Hex “L” 5/32
Spacer Table Lock
Bracket Table Lock Left
Bolt Table Lock
Table Front
Screw Soc Set Lock 10-32 x 3/8
Plate Stop
Knob 1/4-20
Owners Manual
Wrench Hex “L” 3/32
Belt Sanding Assembly
(See Fig. 2)
* Washer 5/8 x 1-3/4 x 1/8
Washer 21/64 x 7/8 x 3/64
Drum Sanding 1"
Drum Sanding 1-1/2"
Drum Sanding 2"
Plate Throat 1-1/2"
Plate Throat 1"
Plate Throat 1/2"
Ring, Retaining 5160-50