Rigol MSO1000Z series - Chapter 11 Waveform Record

262 pages

To Next Page

To Previous Page

Chapter 11 Waveform Record RIGOL

MSO1000Z/DS1000Z User’s Guide 11-1

Chapter 11 Waveform Record

Waveform record can record the waveforms of the analog input channels (CH1-CH4)

and the digital channels (D0-D15). Waveform playback can provide better waveform

analysis effect.

Note: The horizontal time base must be set to Y-T mode during waveform record.

The contents of this chapter:

 Common Settings

 Playback Option

 Record Option

Main Page

Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols6
- Allgemeine Sicherheits Informationen7
- Sicherheits Begriffe und Symbole9
- Measurement Category10
- Ventilation Requirement11
- Working Environment12
- General Care and Cleaning14
- Environmental Considerations14
- Main Features15
MSO1000Z/DS1000Z Series Overview15
Document Overview16
- Table of Contents19
Chapter 1 Quick Start25
- General Inspection26
- Appearance and Dimensions27
- To Prepare the Oscilloscope for Use28
- Front Panel Overview33
- Rear Panel Overview34
- Front Panel Function Overview36
- User Interface43
- Parameter Setting Method47
- To Use the Security Lock48
- To Use the Built-In Help System49
Chapter 2 To Set the Vertical System51
- To Enable the Analog Channel52
- Channel Coupling52
- Bandwidth Limit53
- Probe Ratio53
- Waveform Invert54
- Vertical Scale54
- Amplitude Unit55
- Channel Label55
- Delay Calibration of the Analog Channel57
Chapter 3 To Set the Horizontal System59
- Delayed Sweep60
- Time Base Mode61
Chapter 4 To Set the Sample System65
- Acquisition Mode66
- Sin(X)/X68
- Sample Rate68
- Memory Depth70
- Antialiasing71
Chapter 5 To Trigger the Oscilloscope73
- Trigger Source74
- Trigger Mode75
- Trigger Coupling76
- Trigger Holdoff77
- Noise Rejection77
- Trigger Type78
- Trigger Output Connector109
Chapter 6 MATH and Measurement111
- Math Operation112
- Auto Measurement130
- Cursor Measurement140
Chapter 7 Digital Channel151
- To Select the Digital Channel152
- To Turn On/Off the Digital Channel152
- Group Set153
- To Set the Waveform Display Size154
- Reorder Setting154
- Auto View154
- To Set the Threshold154
- To Set the Label155
- Probe Calibration155
- Digital Channel Delay Calibration156
Chapter 8 Protocol Decoding157
- Parallel Decoding158
- RS232 Decoding (Option)162
- I2C Decoding (Option)167
- SPI Decoding (Option)171
Chapter 9 Reference Waveform175
- To Enable REF Function176
- To Select REF Source176
- To Adjust REF Waveform Display176
- To Save to Internal Memory176
- To Set the Color177
- To Reset the Reference Waveform177
- To Export to Internal or External Memory177
- To Import from Internal or External Memory177
Chapter 10 Pass/Fail Test179
- To Enable Pass/Fail Test180
- To Select Source180
- Mask Range180
- Test and Output181
- To Save the Test Mask181
- To Load the Test Mask182
Chapter 11 Waveform Record183
- Common Settings184
- Playback Option185
- Record Option186
Chapter 12 Display Control187
- To Select the Display Type188
- To Set the Persistence Time188
- To Set the Waveform Intensity189
- To Set the Screen Grid189
- To Set the Grid Brightness189
Chapter 13 Signal Source191
- To Output Basic Waveform192
- To Output Built-In Waveform196
- To Output Arbitrary Waveform200
- Modulation205
Chapter 14 Store and Recall209
- Storage System210
- Storage Type210
- Internal Storage and Recall212
- External Storage and Recall213
- Disk Management214
- Factory219
Chapter 15 Accessibility Setting227
- Remote Interface Configuration228
- System-Related233
Chapter 16 Remote Control239
- Remote Control Via USB240
- Remote Control Via LAN244
- Remote Control Via GPIB246
Chapter 17 Troubleshooting249
Chapter 18 Specifications251
- General Specifications258
- Calibration Interval258
Chapter 19 Appendix259
- Appendix A: Accessories and Options259
- Appendix B: Warranty260
Index261

Rigol MSO1000Z series - Chapter 11 Waveform Record

Table of Contents

Other manuals for Rigol MSO1000Z series

Related product manuals