RNA ESR 3000 Series User Manual

Rhein-Nadel Automation GmbH 10
VT-BA-ESR-ESM3000-EN_2021.docx / 15 March 2021
Designation
Design
ESR 3000 / 6 A – IP54
6 A, housing design with level control
ESR 3000 / 12A – IP 54
12 A, housing design with level control
ESM 3000 / 6A – IP20
6 A, cabinet built-in design with level control
ESM 3000 /16A – IP20
16 A, cabinet built-in design with level control
For use in NFPA 79 applications only E217179
Adapters providing field wiring means are available from Rhein-Nadel Automation GmbH.
Refer to Rhein-Nadel Automation GmbH.
After tuning the controller to the vibratory feeder, the setting required by user is limited to the feed rate.
Feed rate adjustment:
Press 'P' button twice, then set feed rate with the arrow buttons (code C.000).
Parameters:
Code
Factory default
setting:
Access code:
Vibratory feeder
• Vibrating amplitude (feed rate)
0...100 %
A.
0 %
000, 002
The following setting options are available to adjust the vibratory feeder
Parameters:
Display
Factory default
setting:
Access code:
Vibratory feeder
• Vibrating amplitude (feed rate)
0...100 %
A.
0 %
000, 002, 020 096
• Maximum control limitation (U
max
)
5...100 %
P.
90 %
008, 020, 096
• Vibrating frequency
35...140 Hz
(5...300 Hz)
F.
100 Hz
008, 020
040, 096
• Soft entry ramp
0...60 sec.
/.
0.1 sec.
020, 096
• Soft exit ramp
0...60 sec.
\.
0.1 sec.
020, 096
• Switchover to external setpoint
0 / I
E.S.P.
0
003
• Setpoint 0(4)...20 mA
0 / I
4.20
0
003
• Setpoint via potentiometer
0 / I
POT.
0
003
• Coarse / fine control
0 / I
S.P.2.
0
003
• Invert enable signal
0 / I
-En.
0
003
• Indexing control
0 / I
HOP.
0
064
• ON-time (with activated indexing control)
0...60 sec.
H.
1.0 sec.
004, 064
• OFF time (with activated indexing control)
0...60 sec.
h.
1.0 sec.
004, 064
• Hopper sensor inversion (not active)
0 / I
-Ho.
0
004, 064
Level control
• ON delay
0...60 sec.
I.
1 sec.
007, 167
• OFF delay
0...60 sec.
O.
1 sec.
007, 167
• Invert sensor function
PNP / PNP in-
verse
-SE.
PNP
007, 167
• Sensor timeout
0 / I
E.En.
0
015, 167
• Time lag fault (sensor timeout)
1...240 sec.
E.
180 sec.
015, 167
• Valve output stop-delay time
0...60 sec.
A.i.
4 sec.
015
Service
• Show present output current
i.
040
• Show present output frequency
F.
040
• Save user setting
PUSH.
143
• Restore factory default setting
FAC.
210
• Restore user setting
US.PA.
210
• Hide programming menus
0 / I
Hd.C.
0
117
• Hide setpoint adjustment
0 / I
di.S.
0
137
• Show software version number
001
Order designation (standard devices)
Setting options

RNA ESR 3000 Series Specifications

General

Brand	RNA
Model	ESR 3000 Series
Category	Controller
Language	English