Robin FL-H7500 - 2. EQUIPMENT REASSEMBLY; 2. Tightening torque of each part

16
Equipmentreassemblyprocedure

1.Notice
・Cleanpartscompletely.
・Replacescrewswithnewonesifnecessary.
・Tightenupthetighteningtorquespecifiedpartsaccordingtothespecifiedtighteningtorque.


2.Tighteningtorqueofeachpart
 Forfurtherassemblinginstructionsoneachpart,seethecorrespondingpages.



2.EQUIPMENTREASSEMBLY 
ENGINE +20 +2.0
〜CASE2VOLUTE 0 0
IMPELLER +20 +2.0
〜FLYWHEEL 0 0
CASE1VOLUTE +10 +1.0
〜CASE2VOLUTE 0 0
CASE1、2VOLUTE M5×65W,SWS=15 +10 +1.0
(ELBOW) SCREW -5 -0.5
CASE1VOLUTE +10 +1.0
〜COVER,INRET 0 0
DAMPER1 +10 +1.0
〜CASE1,VOLUTE -5 -0.5
FRAME M5×16W,SWMEC +15 +1.5
〜DAMPER1 SCREW 0 0
FRAME +15 +1.5
〜DAMPER2 0 0
CASE,AIRCLEANER +15 +1.5
〜CASE1,2VOLUTE 0 0
FRAME +10 +1.0
〜TANK,FUEL -5 -0.5
GUARD,MUFFLER +5 +0.5
〜COVER,ENGINE 0 0
COVER,ENGINE +10 +1.0
〜CASE2VOLUTE 0 0
STARTER +15 1.5
〜ENGINE 0 0
CASE2,LEVER +5 +0.5
〜LEVER2,THROTTLE 0 0
CASE1,LEVER +3 +0.3
〜CASE2,LEVER 0 0
1
CheckiftheLEVER2,
THROTTLEcanbesmoothly
movedwiththehand,after
fittingitintheCASE2,LEVER
byscrewingthebolt.
4×16
TAPPINGSCREW
5 0.5
5
13
M6×14
SOCKETHEADBOLT
20 2.0
CheckiftheELBOWcanbe
smoothlyrotatedwiththehand,
afterscrewingthescrews.
Thekindofscrew Notice
MUFFLERGASKET
position.
pcs
5×16
TAPPINGSCREW
9
2.0
1
80
M6×30W,SW
SOCKETHEADBOLT
6
7.8
No. Tighteningpart
(kgf･cm)
Tighteningtorque
(N・m)
2
80
M6×40W,SW
SOCKETHEADBOLT
4
7.8
4
20
2
20
3
5×25
TAPPINGSCREW
3
2.0
2.0
20
20
M5×40
SCREW
1
2.0
2
2.5
2.5
2
25
25
5
M6
FRANGENUT
8
25
M5×16W,SW
SCREW
4
2.5
10
25
M6×12W,SW
SCREW
2
2.5
25
M,5×20W,SW
SCREW
3
2.5
20
5×16
TAPPINGSCREW
4
2.0
Besuretoinstallthefueltubes.
4
Besuretoinstallthe
GUARD,MUFFLER.
12
11
4×6
TAPPINGSCREW
10 1.0