Rockwell Automation Reliance SP500 - Index

Index Index-1
INDEX
A
Acceleration Time (F-01), 8-5
AC input
diodes, checking, 9-7 to 9-8
line branch circuit fuses, 3-8, 4-6, 5-2
ratings, 2-7 to 2-8
wire sizes, 3-4 to 3-5
wiring, 3-4 to 3-5, 3-8, 4-1 to 4-6, 5-1 to 5-2
AC line distribution capacity, A-1
AC mains filter, E-1 to E-6
AC output wiring, 3-4 to 3-7, 4-1 to 4-5, 4-7 to 4-9,
5-2, 5-10
Air flow, 3-1, 3-4
Altitude requirements, 3-1, A-1
Analog input jumper (J6), 4-7 to 4-8
Analog Output Select (F-29), 8-17
Analog output wiring, 5-4
Analog speed reference wiring, 5-3 to 5-4
Area required, 3-1 to 3-4
Auto-Restart Number of Attempts (F-26), 8-16
Auto-Restart Retry Wait Time (F-27), 8-17
Avoidance Bandwidth (F-22), 8-14
Avoidance Frequency (F-21), 8-14
B
Board
Capacitor, 2-10 to 2-12, F-1 to F-2
Power, 2-9 to 2-12, F-1
Regulator, 2-9 to 2-12, F-1 to F-2
Braking, snubber resistor , 2-13, A-2
wiring, 4-2 to 4-5, 5-8 to 5-9
C
Carrier frequency, 2-7 to 2-8, A-1
Carrier Frequency (F-10), 8-9
Coast Stop Enable (F-16), 8-12
Conduit size, 4-2 to 4-5
Configurable Output Relay Select (F-09), 8-9
Control Source Select (F-00), 8-5
Control terminal strip, 2-9 to 2-12, 5-3
Control wiring, 5-3 to 5-9
Current Limit (F-05), 8-7
D
DC bus
terminals, 9-2
verifying capacitor voltage, 9-1 to 9-2
Deceleration Time (F-02), 8-5 to 8-6
Digital input wiring
Forward/reverse, 5-7, A-2
Function loss, 5-7, A-2
IET reset, 5-7, A-2
Multi-speed Preset, 5-6 to 5-7
Start/stop, 5-4 to 5-5, A-2
Dimensions, 3-2 to 3-3, A-1
Display
description, 7-1
scaling,
see RPM at Base Speed (F-08)
Drive faults,
see Faults
Drive Voltage Selection (F-28), 8-17
E
Electromagnetic compatibility standards
AC mains filter, E-1 to E-6
Compliance requirements, E-1 to E-2
Declaration of conformity, E-1
Electronic Thermal Overload (F-14), 8-11
Electronic Thermal Overload Enable (F-15),
8-11 to 8-12
Emergency stop, 3-9
Enclosures, NEMA, 2-7 to 2-8
Environmental conditions, 3-1, A-1
Error log, 9-5 to 9-7
F
Fault codes, 9-3 to 9-5
Faults
drive reaction to, 9-1
possible causes and corrective
actions, 9-3 to 9-5
resetting, 9-3
Forward, digital input, 5-5 to 5-7
Frequency, carrier, 2-7 to 2-8, A-1
Function loss, digital input, 5-5 to 5-7