6
Adjusting the Brilliance (Brilliance)
Here’s how to adjust the brilliance of the sound (3 levels).
Hold down
BRIGHT
MELLOW
NORMAL
C5 C6
1
2
3
Adjusting the Reverberation (Ambience)
You can adjust a reverberation of the sound, and get the impression
that you are performing in a concert hall (5 levels).
Hold down
+–
DEFAULT
C5 C6
1 2
3
Dividing the Keyboard in Two (Twin Piano)
You can divide the keyboard into left and right sections so that two
people can play the same pitch ranges. This function lets you use
the unit as though it were two pianos.
C5 C6
Hold down
OFF
PAIR
INDIVIDUAL
1 2
3
The keyboard will be divided into left and right sections, with
“middle C” located in the center of each section.
You can choose one of the following ways in which the sound will
be heard.
Value Explanation
PAIR
The sound will be heard from the right as you play toward
the right of the keyboard, and from the left as you play
toward the left.
INDIVIDUAL
Notes played in the right area will be heard from the right
speaker, and notes played in the left area will be heard
from the left speaker.
* The left and right sections will have the same tone (Piano). Twin
Piano will be cancelled when you push one of the TONE buttons.
* The damper pedal aects only the right section of the keyboard.
Disabling the Buttons (Panel Lock)
While holding down the [PIANO] button, turn the power on. Keep
holding down [PIANO] button for at least six seconds. Panel Lock
will be set, and buttons other than the [ ] (POWER) button will be
disabled. This prevents the tones or settings from being changed if
you inadvertently press a button.
Panel Lock will be cancelled when you turn o the power.
Saving the Settings (Memory Backup)
When this unit’s power is turned o, it will return to its default
settings. However, if desired, you can save the following settings
so that they will be remembered even after the power is o. This is
called the “Memory Backup” function.
Settings saved by Memory Backup Page
Key Touch p. 2
Brilliance p. 6
Ambience p. 6
Master Tuning p. 7
1. Hold down the [KEY TOUCH] button and press the
[RHYTHM] button.
The [OTHER] button and the [SPLIT] button will blink.
To cancel, press the [OTHER] button.
2. To save the settings, press the [SPLIT] button.
When all the LEDs on the buttons are lit, the operation is complete.
Restoring the Factory Settings (Factory Reset)
The settings you’ve changed in the function mode (p. 7) can be
restored to their factory-set condition.
NOTE
When you execute a factory reset, all settings will be
initialized and the song you recorded in internal memory
will be erased.
1. While holding down the [KEY TOUCH] button, turn the
power on. Keep holding down [KEY TOUCH] button for at
least six seconds.
The [OTHER] button and the [SPLIT] button will blink.
To cancel, press the [OTHER] button.
2. To execute the Factory Reset, press the [SPLIT] button.
When all the LEDs on the buttons are lit, the operation is complete.
3. Turn the power o, then on again.
Formatting a USB Flash Drive
Here’s how to initialize (format) the entire contents
saved on a USB ash drive.
NOTE
• Formatting will erase everything that has been saved on the
USB ash drive.
• Before using a new USB ash drive with the F-20 for the rst
time, you must format the USB ash drive.
1. Connect the USB ash drive that you want to format to
the USB MEMORY port.
2. While holding down the [SONG] button, turn the power
on. Keep holding down [SONG] button for at least six
seconds.
The [OTHER] button and the [SPLIT] button will blink.
To cancel, press the [OTHER] button.
3. To execute the format, press the [SPLIT] button.
When all the LEDs on the buttons are lit, the operation is complete.
4. Turn the power o, then on again.
Advanced Features
To Next Page
Loading...
