Roland RD-800 - Selecting Sounds (Tone;Live Set); Selecting a Tone; Layering and Splitting Tones

13
Modulation FX Parameters
18: CHORUS
This is a stereo chorus. A lter is provided so that you can adjust the
timbre of the chorus sound.
L in
R in
Chorus
Chorus
L out
R out
2-Band
EQ
2-Band
EQ
Balance W
Balance W
Balance D
Balance D
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
BALANCE
Species the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Rate Knob
Species the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Filter Type
OFF,
LPF,
HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above
the Cuto Freq
HPF: cuts the frequency range below
the Cuto Freq
Cuto Freq 200–8000 [Hz] Basic frequency of the lter
Pre Delay 0.0–100 [msec]
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate (sync sw) # OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 31)
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread of the sound
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Level 0–127 Output Level
19: FLANGER
This is a stereo anger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking o or landing. A lter is provided so that you can
adjust the timbre of the anged sound.
R in
R out
L in
L out
Flanger
Feedback
Feedback
Flanger
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
FEEDBACK,
BALANCE
Species the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Rate Knob
Species the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Filter Type
OFF,
LPF,
HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above
the Cuto Freq
HPF: cuts the frequency range below
the Cuto Freq
Cuto Freq 200–8000 [Hz] Basic frequency of the lter
Pre Delay 0.0–100 [msec]
Adjusts the delay time from the direct
sound until the anger sound is heard.
Rate (sync sw) # OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 31)
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread of the sound
Feedback # -98–+98 [%]
Adjusts the proportion of the anger
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the anger sound (W)
Level 0–127 Output Level