Roland RD-800 - Editing Sound Effects; Adding Reverb and Modulation Effects

14
Modulation FX Parameters
20: STEP FLANGER
This is a anger in which the anger pitch changes in steps. The
speed at which the pitch changes can also be specied in terms of a
note-value of a specied tempo.
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Step Flanger
Step Flanger
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
FEEDBACK,
STEP RATE,
BALANCE
Species the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Rate Knob
Species the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Filter Type
OFF,
LPF,
HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above
the Cuto Freq
HPF: cuts the frequency range below
the Cuto Freq
Cuto Freq 200–8000 [Hz] Basic frequency of the lter
Pre Delay 0.0–100 [msec]
Adjusts the delay time from the direct
sound until the anger sound is heard.
Rate (sync sw) # OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 31)
Depth 0–127 Depth of modulation
Phase 0–180 [deg] Spatial spread of the sound
Feedback # -98–+98 [%]
Adjusts the proportion of the anger
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Step Rate
(sync sw) #
OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Step Rate (Hz) #/
Step Rate (note)#
0.10–20.00 [Hz]
Rate (period) of pitch change
note (p. 31)
Low Gain -15–+15 [dB] Gain of the low range
High Gain -15–+15 [dB] Gain of the high range
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the anger sound (W)
Level 0–127 Output Level
21: HEXA-CHORUS
Uses a six-phase chorus (six layers of chorused sound) to give
richness and spatial spread to the sound.
Balance W
Balance W
L in
R in
L out
R out
Hexa Chorus
Balance D
Balance D
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
RATE,
BALANCE
Species the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Rate Knob
Species the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Pre Delay 0.0–100 [msec]
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate (sync sw) # OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Rate (Hz) #/
Rate (note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 31)
Depth 0–127 Depth of modulation
Pre Delay
Deviation
0–20
Adjusts the dierences in Pre Delay
between each chorus sound.
Depth Deviation -20–+20
Adjusts the dierence in modulation
depth between each chorus sound.
Pan Deviation 0–20
Adjusts the dierence in stereo
location between each chorus sound.
0: All chorus sounds will be in the
center.
20: Each chorus sound will be spaced
at 60 [deg]ree intervals relative to
the center.
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Level 0–127 Output Level