Roland RD-800 - Function Assignment Options; Assigning Functions to ASSIGN Knobs and Buttons; Assigning Functions to S1;S2 Buttons

30
Modulation FX Parameters
55: FLANGER " DELAY
Feedback
Delay
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Flanger
Balance W
Balance W
Balance D
Balance D
Feedback
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
FLN RATE,
FLN FEEDBACK,
FLN BALANCE,
DELAY
FEEDBACK,
DELAY BALANCE
Species the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Rate Knob
Species the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Flanger Pre
Delay
0.0–100 [msec]
Adjusts the delay time from the direct
sound until the anger sound is heard.
Flanger Rate
(sync sw) #
OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Flanger Rate
(Hz) #/
Flanger Rate
(note) #
0.05–10.00 [Hz]
Frequency of modulation
note (p. 31)
Flanger Depth 0–127 Depth of modulation
Flanger
Feedback #
-98–+98 [%]
Adjusts the proportion of the anger
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Flanger Balance
#
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the anger sound (W)
Delay Time
(sync sw)
OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Delay Time
(msec)/
Delay Time
(note)
1–2600 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
note (p. 31)
Delay Feedback
#
-98–+98 [%]
Adjusts the proportion of the delay
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Delay HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the eect will be cut
(BYPASS: no cut).
Delay Balance #
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the
delay (W) and the sound that is not
sent through the delay (D).
Level 0–127 Output Level
56: CHORUS " FLANGER
Feedback
Flanger
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Chorus
Balance W
Balance W
Balance D
Balance D
a
Parameter Value Explanation
Switch OFF, ON Turns the eect on/o.
Depth Knob
CHORUS RATE,
CHORUS
BALANCE,
FLN RATE,
FLN FEEDBACK,
FLN BALANCE
Species the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Rate Knob
Species the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Chorus Pre Delay 0.0–100 [msec]
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Chorus Rate
(sync sw) #
OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Chorus Rate
(Hz) #/
Chorus Rate
(note) #
0.05–10.00 [Hz]
Modulation frequency of the chorus
eect
note (p. 31)
Chorus Depth 0–127 Modulation depth of the chorus eect
Chorus Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Flanger Pre
Delay
0.0–100 [msec]
Adjusts the delay time from the direct
sound until the anger sound is heard.
Flanger Rate
(sync sw) #
OFF, ON
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner’s manual p. 24).
Flanger Rate
(Hz) #/
Flanger Rate
(note) #
0.05–10.00 [Hz]
Modulation frequency of the anger
eect
note (p. 31)
Flanger Depth 0–127 Modulation depth of the anger eect
Flanger
Feedback #
-98–+98 [%]
Adjusts the proportion of the anger
sound that is fed back into the eect.
Negative “-” settings will invert the
phase.
Flanger Balance
#
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the
anger (W) and the sound that is not
sent through the anger (D).
Level 0–127 Output Level