Roland RD-800 - Using the RD-800 As a Master Keyboard; MIDI Connectivity and Control; Selecting MIDI Output and Adjusting Layer Volume

37
Delay Parameters
3: DELAY " TREMOLO
Parameter Value Explanation
Switch OFF, ON Delay on/o
O Mode
IMMEDIATE,
REMAIN
Species what happens to the delay
decays of the previously-played
phrase when you turn delay o.
IMMEDIATE: The delay sound
disappears immediately.
REMAIN: The delay sound decays
naturally.
Output Select
MAIN,
REV,
MAIN+REV
Species the output destination of the
sound from the delay.
Input Mode
MONAURAL,
STEREO
MONAURAL: The input is mixed to
mono.
Delay (sync sw) OFF, ON
If this is on, the delay is synchronized
with the tempo.
Delay (msec)/
Delay (note)
1–1300 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
note (p. 31)
Feedback -98–+98 [%]
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative “-” settings invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the eect is ltered
out (BYPASS: no cut).
Tremolo Switch OFF, ON Tremolo on/o
Tremolo Mod
Wave
TRI,
SQR,
SIN,
SAW1,
SAW2,
TRP
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
TRP: Trapezoidal wave
Tremolo Rate
(sync sw)
OFF, ON
If this is on, the tremolo is synchro-
nized with the tempo.
Tremolo Rate
(Hz)/
Tremolo Rate
(note)
0.05–10.00 [Hz]
Rate of the tremolo eect
note (p. 31)
Tremolo Depth 0–127 Modulation depth of the anger eect
4: 2TAP DELAY
Parameter Value Explanation
Switch OFF, ON Delay on/o
O Mode
IMMEDIATE,
REMAIN
Species what happens to the delay
decays of the previously-played
phrase when you turn delay o.
IMMEDIATE: The delay sound
disappears immediately.
REMAIN: The delay sound decays
naturally.
Output Select
MAIN,
REV,
MAIN+REV
Species the output destination of the
sound from the delay.
Delay (sync sw) OFF, ON
If this is on, the delay is synchronized
with the tempo.
Delay (msec)/
Delay (note)
1–1300 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
note (p. 31)
Feedback -98–+98 [%]
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative “-” settings invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the eect is ltered
out (BYPASS: no cut).
Delay 1 Pan L64–63R Pan position of delay 1
Delay 2 Pan L64–63R Pan position of delay 2
Delay 1 Level 0–127 Volume of delay 1
Delay 2 Level 0–127 Volume of delay 2
5: 3TAP TAP DELAY
Parameter Value Explanation
Switch OFF, ON Delay on/o
O Mode
IMMEDIATE,
REMAIN
Species what happens to the delay
decays of the previously-played
phrase when you turn delay o.
IMMEDIATE: The delay sound
disappears immediately.
REMAIN: The delay sound decays
naturally.
Output Select
MAIN,
REV,
MAIN+REV
Species the output destination of the
sound from the delay.
Delay Time
(sync sw)
OFF, ON
If this is on, the delay is synchronized
with the tempo.
Delay Time
(msec)/
Delay Time
(note)
1–2600 [msec]
Adjusts the delay time from the direct
sound until the delay sound is heard.
note (p. 31)
Delay 1
Feedback
-98–+98 [%]
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative “-” settings invert the phase.
HF Damp
200–8000 [Hz],
BYPASS
Adjusts the frequency above which
sound fed back to the eect is ltered
out (BYPASS: no cut).
Delay 1 Pan L64–63R Pan position of delay 1
Delay 2 Pan L64–63R Pan position of delay 2
Delay 3 Pan L64–63R Pan position of delay 3
Delay 1 Level 0–127 Volume of delay 1
Delay 2 Level 0–127 Volume of delay 2
Delay 3 Level 0–127 Volume of delay 3