Roland V-Drums TD-27 - Output

36
SYSTEM
OUTPUT
Here’s how to assign the audio outputs from the MASTER OUT jacks, DIRECT OUT jacks, and PHONES jack.
Parameter Value Explanation
[F1] button (PAD MAS tab)
PAD OUTPUT ASSIGN MASTER
PHONES (MASTER OFF),
PHONES+MASTER LR
Species each pad’s output from the PHONES jack and the MASTER OUT jacks (when Master Out
(p. 36) is “NORMAL”).
[F2] button (PAD DIR tab)
PAD OUTPUT ASSIGN DIRECT
OFF, 1, 2, 1+2, MASTER DIRECT L,
MASTER DIRECT R, MASTER DIRECT
L+R
Species each pad’s output from the DIRECT OUT1, 2 jacks and the MASTER OUT jacks (when
Master Out (p. 36) is “DIRECT”).
[F3] button (OTHER MAS tab)
OTHER OUTPUT ASSIGN
MASTER
PHONES (MASTER OFF),
PHONES+MASTER LR
Species how ROOM and MFX are output from the PHONES jack and the MASTER OUT jacks (when
Master Out (p. 36) is “NORMAL”).
[F4] button (OTHER DIR tab)
OTHER OUTPUT ASSIGN
DIRECT
OFF, 1, 2, 1+2, 3, 4, 3+4, 5, 6, 5+6, 7,
8, 7+8, MASTER DIRECT L, MASTER
DIRECT R, MASTER DIRECT L+R
Species how ROOM and MFX are output from the DIRECT OUT1, 2 jacks and the MASTER OUT jacks
(when Master Out (p. 36) is “DIRECT”).
OUTPUT ROUTING
Here’s how to make settings for output routing to the MASTER OUT jacks, DIRECT OUT jacks, and PHONES jack.
Parameter Value Explanation
[F1] button (ROUTING tab)
PadEq/Comp to Direct*1
OFF, ON
Species whether the pad equalizer (p. 15) and pad compressor (p. 16) eects are applied (ON) or
are not applied (OFF) to the sound that is output from the DIRECT OUT jacks.
If this is “OFF,” the pad equalizer and pad compressor are bypassed for the output of the DIRECT
OUT jacks.
If the OUTPUT ROUTING Master Out is “DIRECT,” and PadEq/Comp to Direct is “OFF,” the output from
the MASTER OUT jacks also bypasses the pad equalizer and pad compressor.
PadComp to Phones
OFF, ON
Species whether the pad compressor (p. 16) is applied (ON) or is not applied (OFF) to the sound
that is output from the PHONES jack.
If this is “OFF,” the pad compressor does not aect the output from the PHONES jack.
For example, this lets you use the pad compressor to reduce the dynamic range for the drum
monitor or PA, but hear the full dynamics in the monitor headphones while you perform.
Master Out*1
NORMAL, DIRECT
Selects whether the output of the MASTER OUT jacks is the same signal as the DIRECT OUT jacks
(DIRECT) or not (NORMAL).
If this is “DIRECT,” the output of the MASTER OUT jacks is not aected by the master compressor
and master EQ, allowing you to use the MASTER OUT jacks as DIRECT OUT jacks (the setting of the
[MASTER] knob does apply).
This setting also applies to the USB audio output to your computer.
[F2] button (LO CUT tab)
LoCut Frequency
20–200 Hz
Cuts the frequency region below the specied frequency (low cut).
This setting is common to all output jacks.
DirectOut*2
OFF, ON
Species whether low cut is applied (ON) or is not applied (OFF) to the sound that is output from
the DIRECT OUT jacks.
MasterOut*2
OFF, ON
Species whether low cut is applied (ON) or is not applied (OFF) to the sound that is output from
the MASTER OUT jacks.
PhonesOut
OFF, ON
Species whether low cut is applied (ON) or is not applied (OFF) to the sound that is output from
the PHONES jack.