Roland V-Drums TD-27 - Chorus; Ds 0 Chorus; Ds 0 Delay; Od 0 Chorus

44
Multi-Eect Parameters
OD
0
DELAY
Parameter Value Explanation
Overdrive
Drive
0–127
Degree of distortion
Also changes the volume.
Overdrive Pan
L64–R63 Stereo location of the overdrive sound
Tempo Sync
OFF, ON
Species whether the delay time value of
the delay is specied as a note value (ON) or
not (OFF).
Delay Time
1–2600msec, note
Adjusts the delay time from the direct sound
until the delay sound is heard.
Delay
Feedback
-98–+98%
Adjusts the proportion of the delay sound
that is fed back into the eect. Negative “-”
settings will invert the phase.
Delay HF
Damp
200–8000Hz,
BYPASS
Adjusts the frequency above which sound
fed back to the eect will be cut. If you do
not want to cut the high frequencies, set this
parameter to BYPASS.
Delay Balance
D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the delay (W)
and the sound that is not sent through the
delay (D).
Level
0–127 Output Level
DS
0
DELAY
The parameters are essentially the same as in “OD
0
DELAY” with the
exception of the following two.
Overdrive Drive
0
Distortion Drive, Overdrive Pan
0
Distortion Pan
CHORUS
This is a stereo chorus. A lter is provided so that you can adjust the
timbre of the chorus sound.
Parameter Value Explanation
Filter Type
OFF, LPF, HPF
Type of lter
OFF: no lter is used
LPF: cuts the frequency range above the
Cuto Freq
HPF: cuts the frequency range below the
Cuto Freq
Cuto Freq
200–8000Hz
Species the frequency at which the lter
cuts a specic frequency region
Pre Delay
0.0–100.0ms
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Tempo Sync
OFF, ON
Species whether the modulation rate is
specied as a note value (ON) or not (OFF).
Rate
0.05–10.00Hz,
note
Frequency of modulation
Depth
0–127 Depth of modulation
Phase
0–180deg Spatial spread of the sound
Low Gain
-15–+15dB Gain of the low range
High Gain
-15–+15dB Gain of the high range
Level
0–127 Output Level
SPACE-D
This is a multiple chorus that applies two-phase modulation in stereo.
It gives no impression of modulation, but produces a transparent
chorus eect.
Parameter Value Explanation
Pre Delay
0.0–100.0ms
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Tempo Sync
OFF, ON
Species whether the modulation rate is
specied as a note value (ON) or not (OFF).
Rate
0.05–10.00Hz,
note
Frequency of modulation
Depth
0–127 Depth of modulation
Phase
0–180deg Spatial spread of the sound
Low Gain
-15–+15dB Gain of the low range
High Gain
-15–+15dB Gain of the high range
Level
0–127 Output Level
OD
0
CHORUS
Parameter Value Explanation
Overdrive
Drive
0–127
Degree of distortion
Also changes the volume.
Overdrive Pan
L64–R63 Stereo location of the overdrive sound
Chorus Pre
Delay
0.0–100.0ms
Adjusts the delay time from the direct sound
until the chorus sound is heard.
Tempo Sync
OFF, ON
Species whether the modulation rate is
specied as a note value (ON) or not (OFF).
Rate
0.05–10.00Hz,
note
Frequency of modulation
Chorus Depth
0–127 Depth of modulation
Chorus
Balance
D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the chorus (W)
and the sound that is not sent through the
chorus (D).
Level
0–127 Output Level
DS
0
CHORUS
The parameters are essentially the same as in “OD
0
CHORUS” with
the exception of the following two.
Overdrive Drive
0
Distortion Drive, Overdrive Pan
0
Distortion Pan