Roland V-Drums TD-27 - 3 Tap Pan Delay; Delay; Reverse Delay; Tape Echo

43
Multi-Eect Parameters
DELAY
This is a stereo delay.
Parameter Value Explanation
Tempo Sync
Left, Right
OFF, ON
Species whether the delay time value of the
left/right delay sounds is specied as a note
value (ON) or not (OFF).
Delay Left,
Right Time
1–1300msec, note
Delay time from the original sound until the
left/right delay sound is heard
Phase Left,
Right
NORMAL, INVERSE Phase of the delay sound
Feedback
Mode
NORMAL, CROSS
Selects the way in which delay sound is fed
back into the eect
NORMAL: The left/right delay sounds are fed
back without modication.
CROSS: The left/right delay sounds are
alternately exchanged when fed back.
Feedback
-98–+98%
Adjusts the amount of the delay sound that’s
fed back into the eect.
Negative “-” settings will invert the phase.
HF Damp
200–8000
Hz, BYPASS
Adjusts the frequency above which sound
fed back to the eect is ltered out. If you
don’t want to lter out any high frequencies,
set this parameter to BYPASS.
Low Gain
-15–+15dB Gain of the low frequency range
High Gain
-15–+15dB Gain of the high frequency range
Level
0–127 Output Level
TAPE ECHO
A virtual tape echo that produces a realistic tape delay sound. This
simulates the tape echo section of a Roland RE-201 Space Echo.
Parameter Value Explanation
Mode
S, M, L, S+M, S+L,
M+L, S+M+L
Combination of playback heads to use Select
from three dierent heads with dierent
delay times
S: Short
M: Middle
L: Long
Repeat Rate
0–127
Tape speed
Increasing this value will shorten the spacing
of the delayed sounds.
Intensity
0–127 Amount of delay repeats
Bass
-15–+15dB
Boost/cut for the lower range of the echo
sound
Treble
-15–+15dB
Boost/cut for the upper range of the echo
sound
Head S Pan
L64–R63
Independent stereo location for the short,
middle, and long playback heads
Head M Pan
L64–R63
Head L Pan
L64–R63
Tape
Distortion
0–5
Amount of tape-dependent distortion to be
added
This simulates the slight tonal changes
that can be detected by signal-analysis
equipment. Increasing this value will increase
the distortion.
W/F Rate
0–127
Speed of wow/utter (complex variation in
pitch caused by tape wear and rotational
irregularity)
W/F Depth
0–127 Depth of wow/utter
Level
0–127 Output level
REVERSE DELAY
This is a reverse delay that adds a reversed and delayed sound to the
input sound. A tap delay is connected immediately after the reverse
delay.
Parameter Value Explanation
Threshold
0–127
Volume at which the reverse delay will
begin to be applied
Tempo Sync
Rev
OFF, ON
Species whether the delay time value of
the reverse delay is specied as a note value
(ON) or not (OFF).
Rev Delay
Time
1–1300msec, note
Delay time from when sound is input into
the reverse delay until the delay sound is
heard
Rev Delay
Feedback
-98–+98%
Proportion of the delay sound that is to be
returned to the input of the reverse delay.
(negative values invert the phase)
Rev Delay HF
Damp
200–8000Hz,
BYPASS
Frequency at which the high-frequency
content of the reverse-delayed sound will
be cut (BYPASS: no cut)
Rev Delay Pan
L64–R63 Stereo location of the reverse delay sound
Rev Delay
Level
0–127 Volume of the reverse delay sound
Tempo Sync
Delay 1–3
OFF, ON
Species whether the delay time value of
the tap delay is specied as a note value
(ON) or not (OFF).
Delay 1–3
Time
1–1300msec, note
Delay time from when sound is input into
the tap delay until the delay sound is heard
Delay 3
Feedback
-98–+98%
Proportion of the delay sound that is to
be returned to the input of the tap delay
(negative values invert the phase)
Delay HF
Damp
200–8000Hz,
BYPASS
Frequency at which the high frequency
content of the tap delay sound will be cut
(BYPASS: no cut)
Delay 1 Pan,
Delay 2 Pan
L64–R63 Stereo location of the tap delay sounds
Delay 1 Level,
Delay 2 Level
0–127 Volume of the tap delay sounds
Low Gain
-15–+15dB Gain of the low frequency range
High Gain
-15–+15dB Gain of the high frequency range
Level
0–127 Output Level
3TAP PAN DELAY
Produces three delay sounds; center, left and right.
Parameter Value Explanation
Tempo Sync
Left, Right,
Center
OFF, ON
Species whether the delay time value of the
left/right/center delay sound is specied as a
note value (ON) or not (OFF).
Delay Left,
Right, Center
Time
1–2600msec, note
Adjusts the time until the delay sound is
heard.
Center
Feedback
-98–+98%
Adjusts the amount of the delay sound that’s
fed back into the eect. Negative “-” settings
invert the phase.
HF Damp
200–8000Hz,
BYPASS
Adjusts the frequency above which sound
fed back to the eect is ltered out. If you do
not want to lter out any high frequencies,
set this parameter to BYPASS.
Left, Right,
Center Level
0–127 Volume of each delay
Low Gain
-15–+15dB Gain of the low frequency range
High Gain
-15–+15dB Gain of the high frequency range
Level
0–127 Output Level