Roland V-Synth GT Supplementary Manual

14
List of Added Tone-FX
62: Cho/Flg -> Stereo Delay
(Chorus/Flanger -> Stereo Delay)
This effect connects either Chorus or Flanger and Delay in
series.
fig.MFX-30
Parameter
Value Description
Mod Mode
(Chorus
/ Flanger)
CHORUS,
FLANGER
Selects whether to use chorus or
flanger.
Mod Rate #1
0.05–10.0 Hz,
note
Adjusts the speed of modulation for
the chorus or flanger.
Mod Depth 0–127
Adjusts the depth of modulation for
the chorus or flanger.
Mod Phase 0–180 deg
Sets how the chorus or flanger sound
is spread.
Mod Pre Delay 0–50.0 ms
Adjusts the delay time from the direct
sound until the chorus or flanger
sound is heard.
Mod Feedback -98– +98%
Adjusts the proportion of the effect
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Xover LowFreq 50–4000 Hz
Attenuates the effect in the range
below the specified frequency.
Xover Low Gain -36–0 dB
Specifies how greatly the low range
will be attenuated.
Xover HiFreq 2000–20000 Hz
Attenuates the effect in the range
above the specified frequency.
Xover Hi Gain -36–0 dB
Specifies how greatly the high range
will be attenuated.
Mod Level 0–127 Volume of the chorus or flanger sound.
Mode
MONO, STEREO,
ALTERNATE
Switches stereo, monaural, or
alternate.
MONO: This is a single-input, dual-
output delay. Stereo sound (left and
right) are mixed before being input.
STEREO: This is a dual-input, dual-
output delay. The delay sound output
features the same stereo placement as
that of the input.
ALTERNATE: The left and right delay
sound output alternately. (Alternate
delay)
Delay Time
0–1300 ms
(MONO), 0–650
ms (STEREO,
ALTERNATE),
note
Adjusts the delay time from the direct
sound until the delay sound is heard.
L-R Shift 0–650 ms, note
Of the left and right delay sounds, the
delay time will be increased for only
one side.
If the L-R order is L → R, the R sound will
be later. In the case of R → L, the L
sound will be later.
When the mode is set to MONO or
ALTERNATE, this setting will be
ignored.
L
R
Chorus/
Flanger
2-Band
EQ
Delay
L-R Order
L → R, R → L
In STEREO or ALTERNATE mode, this
setting determines which of the left or
right sides has the delay sound before
the other
L → R: The left side is expressed first
R → L: The right side is expressed first
In MONO mode, this setting will be
ignored.
Feedback #2 -98– +98%
Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Low Damp Freq 50–4000 Hz
Adjusts the frequency below which
sound fed back to the effect will be cut.
The lower range is attenuated earlier
than other ranges (low-damp effect).
Low Damp Gain -36–0 dB Degree of Low Damp
Hi Damp Freq 2000–20000 Hz
Adjusts the frequency above which
sound fed back to the effect will be cut.
High Damp, by attenuating the higher
frequencies first, makes the delay
sound more natural.
Hi Damp Gain -36–0 dB Degree of High Damp
Balance #3
DRY100:0WET–
DRY0:100WET
Volume balance between the direct
sound (DRY) and the delay sound
(WET)
Ps Low Freq 50–4000 Hz Frequency of the low range
Ps Low Gain -15– +15 dB Gain of the low range
Ps Hi Freq 2000–20000 Hz Frequency of the high range
Ps Hi Gain -15– +15 dB Gain of the high range
Level 0–127 Output level
Parameter Value Description
V-Synth_GT_v2_e1.book 14 ページ ２００８年１２月１７日 水曜日 午前９時５分

Roland V-Synth GT Specifications

General

Brand	Roland
Model	V-Synth GT
Category	Synthesizer
Language	English