Samsung CLX-8540ND - Page 213

Troubleshooting
Service Manual
4-51
Samsung Electronics
Code Displayed Name Meaning
Input /
Output
State
Displayed
107-100 iTHV(-) Bias iTHV minus bias voltage on at normal drive level Output On[Off]
107-110 Detach Bias Detack bias voltage on at normal drive level Output On[Off]
107-170 Saw Bias Saw bias voltage on at normal drive level Output On[Off]
109-000 Fuser Temperature A Detects what the temperature A is on fuser. Input Numeric 3 digits
109-010 Fuser Temperature B Detects what the temperature B is on fuser. Input Numeric 3 digits
109-030 Fuser Motor Forward Fuser Motor Forward On/Off Output On[Off]
109-110 Fuser Crum Read1 Detect if the life of fuser1 is exhausted. Input High[Low]
109-120 Fuser Crum Read2 Detect if the life of fuser2 is exhausted. Input High[Low]
109-150 Fuser Bias(+) Bias Fuser Positive bias voltage on at normal drive level Output On[Off]
109-151 Fuser Bias(-) Bias Fuser Negative bias voltage on at normal drive level Output On[Off]
110-000 LSU Motor1 Run Ready Detects if LSU motor1 runs at normal speed. Input High[Low]
110-010 LSU Motor2 Run Ready Detects if LSU motor2 runs at normal speed. Input High[Low]
110-020 LSU Fan1 Run Ready Detects if LSU Fan Motor runs at normal speed. Input High[Low]
110-040 LSU Clean Motor Detect if the LSU Clean Motor On/Off Output High[Low]
110-050 LSU Clean Sensor Detect if the LSU Clean Motor is On or Off Input High[Low]
110-060 LSU Motor1 Run LSU Motor1 On/Off Output On[Off]
110-070 LSU Motor2 Run LSU Motor2 On/Off Output On[Off]
110-080 LSU LD Power1 LSU LD1 Power On/Off (yellow) Output On[Off]
110-090 LSU LD Power2 LSU LD2 Power On/Off (magenta) Output On[Off]
110-100 LSU LD Power3 LSU LD3 Power On/Off (cyan) Output On[Off]
110-110 LSU LD Power4 LSU LD4 Power On/Off (black) Output On[Off]
110-120 LSU Fan1 Run Start/Stop LSU Fan Run Output On[Off]
111-000 Toner Dispense Motor Yellow Toner Dispense(Supply) Motor On/Off Output On[Off]
111-010
Toner Dispense Motor
Magenta
Toner Dispense(Supply) Motor On/Off Output On[Off]
111-020 Toner Dispense Motor Cyan Toner Dispense(Supply) Motor On/Off Output On[Off]
111-030 Toner Dispense Motor Black Toner Dispense(Supply) Motor On/Off Output On[Off]
111-040 Toner Sensor Yellow TC sensor in developer tank. Input Numeric 3 digits
111-050 Toner Sensor Magenta TC sensor in developer tank. Input Numeric 3 digits
111-060 Toner Sensor Cyan TC sensor in developer tank. Input Numeric 3 digits
111-070 Toner Sensor Black TC sensor in developer tank. Input Numeric 3 digits
111-100 ID Sensor(Vo1/S) Check Display ID Sensor(Vo1,S) reading value Input Numeric 4 digits
111-110 ID Sensor(Vo2/P) Check Display ID Sensor(Vo2,P) reading value Input Numeric 4 digits
113-000 Finisher Present Sensor Detect if the Finisher is in place. Input Install[Not Install]
113-010 Entrance Motor Entrance Motor run as IOT Speed <about 5 sec> Output On[Off]
113-020 Exit Motor Exit Motor run as IOT Speed <about 5 sec> Output On[Off]
113-030 Paddle Motor Paddling Output On
113-040 Front Jog Home Front Jogger move Home Output On