Sanyo MCO-19M - Other Incubator Settings; Configuring Date, Time, and Logging

- 36 -
㻌
㻌
㻌
5. Various alarms
㻌
<Setting of alarms>
㻌
㻌
䣑 䣍
䣷 䣵䣕 䣶 䣣 䣶
䣖 䣱 䣱 䣮 䣵
䣎 䣱 䣩
䣕 䣧 䣶
䢷 䢰 䢲䢲䢵 䢹 䢰
䣗䣏 䣇 䣐
䣑 䢴䢰 䢲 䢧䢴 䢷䣅 䣑䢰 䢲 䤑䣅䣲 䢵 䢹䣖 䣧 䣯
㻌
㻌
㻌
䣧䣖 䣫 䣯䣆 䣣 䣶 䣧
䣫 䣰 䣩䣕 䣧 䣶 䣶䣒 䣙䣎 䣱 䣥 䣭䣍 䣧 䣻
䣰 䣩䣧 䣶 䣶 䣫䣗 䣘 䣕
䣥 䣧 䣮䣅 䣣 䣰
䣫 䣰 䣩䣕 䣧 䣶 䣶䣆 䣃 䣓䣎 䣅 䣆 䢱
䣕 䣸 䣥
䣫 䣰 䣩䣕 䣧 䣶 䣶䣣 䣴 䣯
䣑
䣃 䣮
䣍
䣰䣣 䣶 䣫 䣱䣮 䣫 䣤 䣴䢴 䣅 䣣䣑 䢴 䢱 䣑䣯 䣲 䢱 䣅䣖 䣧
䣗䣏 䣇 䣐
䢫䢪 䢳 䢱 䢴
䣱 䣮 䣵䣶 䣖 䣱䣧 䣮 䣧 䣥䣕
㻌
㻌
㻌
䣃 䣮 䣣 䣴 䣯 䣕 䣧 䣶 䣶 䣫 䣰 䣩
䣖 䣧 䣯 䣲 䣃 䣮 䣣 䣴 䣯 䤒 䢳 䢰 䢲
䤑
䣅 䢪 䤒 䢳 䢰 䢲
䤑
䣅 䢯 䤒 䢷 䢰 䢲
䤑
䣅 䢫
䣅 䣑 䢴 䣃 䣮 䣣 䣴 䣯 䤒 䢳 䢰 䢲 䢧 䢪 䤒 䢲 䢰 䢷 䢧 䢯 䤒 䢷 䢰 䢲 䢧 䢫
䣑 䢴 䣃 䣮 䣣 䣴 䣯 䤒 䢳 䢰 䢲 䢧 䢪 䤒 䢲 䢰 䢷 䢧 䢯 䤒 䢷 䢰 䢲 䢧 䢫
䣃 䣮 䣣 䣴 䣯 䣆 䣧 䣮 䣣 䣻 䢳 䢷 䣯 䣫 䣰 䢪 䢲 䢯 䢳 䢷 䣯 䣫 䣰 䢫
䣔 䣫 䣰 䣩 䣄 䣣 䣥 䣭 䢵 䢲 䣯 䣫 䣰 䢪 䢲 䢰 䣑 䣈 䣈 䢳 䢯 䢻 䢻 䣯
䣫 䣰 䢫
䣆 䣱 䣱 䣴 䣆 䣧 䣮 䣣 䣻 䢴 䣯 䣫 䣰 䢪 䢳 䢯 䢵 䢲 䣯 䣫 䣰 䢫
㻌
Setting range of high temperature alarm is +1.0~+5.0䉝 䠄Factory default: +1.0䉝䠅
Setting range of low temperature alarm is -1.0~-5.0䉝 䠄Factory default: -1.0䉝䠅
(Note) When you input a value lower than “1.0”, it is memorized as +/- 1.0䉝.
When you input a value over than “5.0”, it is memorized as +/- 5.0䉝
Setting range of high CO2 density alarm is +0.5~+5.0% 䠄Factory default: +1.0%䠅
Setting range of low CO2 density alarm is -0.5~-5.0% 䠄Factory default: -1.0%䠅
(Note) When you input a value lower than “0.5”, it is memorized as +/- 0.5%.
When you input a value over than “5.0”, it is memorized as +/- 5.0%.
Setting range of high O2 density alarm is +0.5~+5.0% 䠄Factory default: +1.0%䠅
Setting range of low O2 density alarm is -0.5~-5.0% 䠄Factory default: -1.0%䠅
(Note) When you input a value lower than “0.5”, it is memorized as +/- 0.5%.
When you input a value over than “5.0”, it is memorized as +/- 5.0%.